Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 44
items per page: 25 50 75
Sort by:

Abstract

The objective of the research was to determine the influence of boron on the crystallization process and microstructure of ductile cast iron. In the case of ductile cast iron it is a vital issue because even as little as trace presence of boron changes the properties of ductile cast iron in a significant way. With the use of a new ATD-4 (TDA) tester and CRYSTALDIGRPAH converter it was possible to measure the crystallization process parameters of the same alloy with four different contents of boron in one mould. Four samples with different boron contents were extracted, their microhardness was measured and quantitative analysis of microstructure was conducted. Obtained results allowed to state that with increasing content of boron the amount of graphite precipitates decreases, the amount of pearlite precipitates increases, the shape of graphite precipitates deteriorates and hardness increases. It is also planned to perform additional testings with boron contents between previously tested values.
Go to article

Abstract

This article discusses results of an analysis of mechanical properties of a sintered material obtained from a mixture of elemental iron, copper and nickel powders ball milled for 60 hours. The powder consolidation was performed by hot pressing in a graphite mould. The hot pressing was carried out for 3 minutes at 900 °C and under a pressure of 35 MPa. The sintered specimens were tested for density, porosity, hardness and tensile strength. Their microstructures and fracture surfaces were also examined using a scanning electron microscope (SEM). The study was conducted in order to determine the suitability of the sintered material for the manufacture of metal-bonded diamond tools. It was important to assess the effects of chemical composition and microstructure of the sintered material on its mechanical properties, which were compared with those of conventional metal bond material produced from a hot-pressed SMS grade cobalt powder. Although the studied material shows slightly lower strength and ductility as compared with cobalt, its hardness and offset yield strength are sufficiently high to meet the criteria for less demanding applications.
Go to article

Abstract

In earlier works were described trends in the production of tools for die casting (hot work). Almost the entire set of issues dealt with may seem insignificant when incompletely assembled acceptance of the material and the associated risks of processing a material with an inappropriate structure, leading to a very early defect of the die. Therefore, further work will focus particularly on identifying the causes of thermal cracks and preventing a suitable choice of acceptance criteria conditions and heat treatment.
Go to article

Abstract

This paper deals with the evaluation of the corrosion resistance of the Al-Si alloys alloyed with the different amount of antimony. Specifically it goes about the alloy AlSi7Mg0,3 which is antimony alloyed in the concentrations 0; 0,001; 0,005; 0,01 a 0,05 wt. % of antimony. The introduction of the paper is dedicated to the theory of the aluminium alloys corrosion resistance, testing and evaluation of the corrosion resistance. The influence of the antimony to the Al-Si alloys properties is described further in the introduction. The experimental part describes the experimental samples which were prepared for the experiment and further they were exposed to the loading in the atmospheric conditions for a period of the 3 months. The experimental samples were evaluated macroscopically and microscopically. The results of the experiment were documented and the conclusions in terms of the antimony impact to the corrosion resistance of the Al-Si alloy were concluded. There was compared the corrosion resistance of the Al-Si alloy antimony alloyed (with the different antimony content) with the results of the Al-Si alloy without the alloying after the corrosion load in the atmospheric conditions in the experiment.
Go to article

Abstract

Determination of the ferrite content in austenitic steels, which solidified under defined conditions. Ferrite content in austenitic matrix was determined from samples with wall thickness of 60 mm. Measured ferrite contents served to propose the regression equations for the calculation of the ferrite content in steels with Cr content of 18 up to 22 % and Ni of 9 up to 11 %. An additional regression equation was proposed for steels with a higher Ni content. The proposed regression equations have been checked up on the operating melts. In conclusion, the ferrite content in the axis of the casting of wall thickness of 500 mm has been calculated and it was compared to the ferrite determined in the usual way from the cast-on test.
Go to article

Abstract

The paper describes existing requirements for tool materials. In the light of experience with these supplied materials, we have demonstrated their considerable influence on the life of molds for die casting technology. From this research came the evaluation methodology of these tool materials which has been used for directing the development of a new material. Based on the new regulation of the chemical composition a sample was casted and forged after that. Then was determined the process of heat treatment and from a block of this material a mold insert was produced. This insert is now being tested in production.
Go to article

Abstract

The paper presents the possibility of the usage of the concfocal microscope for define the type of tribological wear present during the technical dry friction on the testing machine of the pin-on-disc T-01M. The pin was a remelted high-speed steel and the disc was made from sintered carbides. The surface layer of the high-speed steel was remelted with the electric arc with different parameters. The intensity of the electric arc current was changed, the scanning speed and the single, overlapping remeltings were used. On the basis of the 3D, 2D view of the surface friction of the pin (made from the remelted high-speed steel), disc (made from the sintered carbides) and the surface roughness profile run along the marked line, the presence of the abrasive wear can be defined with the description of the elementary wear processes due to the abrasive and/or adhesive wear.
Go to article

Abstract

The excellent property combination of thin wall ductile iron castings (TWDI), including thin wall alloyed cast iron (e.g. austenitic TWDI) has opened new horizons for cast iron to replace steel castings and forgings in many engineering applications with considerable cost benefits. TWDI is considered as a potential material for the preparation of light castings with good mechanical and utility properties, the cost of which is relatively low. In this study, unalloyed and high Ni-alloyed (25% Ni) spheroidal graphite cast iron, with an austenitic metallic matrix were investigated. The research was conducted for thin-walled iron castings with 2, 3 and 5mm wall thickness, using different mould temperature (20°C, and 160°C) to achieve various cooling rates. The metallographic examinations i.e. characteristic of graphite nodules, metallic matrix, and primary grains of austenite dendrites (in high-nickel NTWDI) and mechanical properties were investigated. The study shows that homogeneity of the casting structure of thin-walled castings varies when changing the wall thickness and mould temperature. Finally, mechanical properties of thin-walled ductile iron castings with ferritic-pearlitic and austenitic metallic matrix have been shown.
Go to article

Abstract

In this work, the effect of the microstructure on corrosion behavior of selected Mg- and Al-based as cast alloys, was evaluated. The electrochemical examinations were carried out, and then a morphology of corrosion products formed due to local polarization on materials surface, was analyzed. It was documented that the presence of Mg2Si phase plays an important role in the corrosion course of Mg-based alloy. A selective etching was observed in sites of Mg2Si precipitates having “Chinese script”- like morphology. Analogous situation was found for Al-based alloy, where the key role was played by cathodic θ-CuAl2 phase.
Go to article

Abstract

In this study, the modification mechanism and growth process of Al3(Sc, Zr) particles in as-cast Al-Si-Mg-Cu based alloy with addition of Sc and Zr were systematically investigated. It was found that 0.57 wt-%Sc addition caused a significant refinement in the average grain size of the investigated alloy, which brought about a remarkable transformation in as-cast microstructure, from thick dendritic shape to fine equiaxed structure. A large amount of primary Al3(Sc, Zr) particles with the dimension of around 5-6 μm were also observed within the equiaxed grain. Due to the identical orientation and similar crystal structure between primary Al3(Sc, Zr) particles and α-Al matrix, the primary particles always served as heterogeneous nucleus for the α-Al matrix. In addition, these cusped cubic primary Al3(Sc, Zr) particles showed triangle, star, rhomboid morphologies are generated from sectioning the particle in (111), (100) and (110) planes, respectively. Particularly, the typical eutectic structure which contained odd number-layer (Al3(Sc, Zr)+α-Al+  +Al3(Sc, Zr)) was observed within the investigated particles.
Go to article

Abstract

The article presents results of studies of silicon – molybdenum cast iron (4.42% Si, 2.59% Mo and 2.48% C wt.-%) crystallization process. Metallographic analysis was carried out using SEM-scanning electron microscopy with the EDS system. In order to determine the phase composition, X-ray diffraction studies were performed. Thermo-Calc, a computer simulation program, was used to simulate the crystallization process. . The obtained data allowed to describe the effect of some elements on the crystallization process. The silicon phase of MnSi could not be identified during metallographic studies. Also, computer simulation of the crystallization process did not answer the question at which point the silicon phase of MnSi crystallizes in the tested alloy. Therefore, not all results obtained were linked to the registered crystallization process (TDA process). The EDS analysis revealed an unusual distribution of molybdenum in the microstructure of the sample, where it is clearly visible that the area enriched with this element is also the separation of spheroidal graphite. The possibility of occurrence of Mo-rich micro-areas found in graphite is considered. The case is debatable and difficult to resolve at this stage. Perhaps, at such a high concentration of molybdenum (2.59% Mo) in the alloy, conditions are created for simultaneously crystallization of graphite and molybdenum phases.
Go to article

Abstract

Non-metallic inclusions found in steel can affect its performance characteristics. Their impact depends not only on their quality, but also, among others, on their size and distribution in the steel volume. The literature mainly describes the results of tests on hard steels, particularly bearing steels. The amount of non-metallic inclusions found in steel with a medium carbon content melted under industrial conditions is rarely presented in the literature. The tested steel was melted in an electric arc furnace and then desulfurized and argonrefined. Seven typical industrial melts were analyzed, in which ca. 75% secondary raw materials were used. The amount of non-metallic inclusions was determined by optical and extraction methods. The test results are presented using stereometric indices. Inclusions are characterized by measuring ranges. The chemical composition of steel and contents of inclusions in every melts are presented. The results are shown in graphical form. The presented analysis of the tests results on the amount and size of non-metallic inclusions can be used to assess them operational strength and durability of steel melted and refined in the desulfurization and argon refining processes.
Go to article

Abstract

The present research was conducted on thin-walled castings with 5 mm wall thicknesses. This study addresses the effect of the influence of different master alloys, namely: (1) Al-5%Ti-1%B, (2) Al-5%Ti and (3) Al-3%B, respectively on the structure and the degree of undercooling (ΔTα = Tα-Tmin, where Tα - the equilibrium solidification temperature, Tmin - the minimum temperature at the beginning of α(Al) solidification) of an Al-Cu alloy. The process of fading has been investigated at different times spent on the refinement treatment ie. from 3, 20, 45 and 90 minutes respectively, from the dissolution of master alloys. A thermal analysis was performed (using a type-S thermocouple) to determine cooling curves. The degree of undercooling and recalescence were determined from cooling and solidification curves, whereas macrostructure characteristics were conducted based on a metallographic examination. The fading effect of the refinement of the primary structure is accompanied by a significant change in the number (dimension) of primary grains, which is strongly correlated to solidification parameters, determined by thermal analysis. In addition to that, the analysis of grain refinement stability has been shown with relation to different grain refinements and initial titanium concentration in Al-Cu base alloy. Finally, it has been shown that the refinement process of the primary structure is unstable and requires strict metallurgical control.
Go to article

Abstract

The paper presents the research results of the solenoid housing made of the Zn4Al1Cu alloy that was destroyed as a result of corrosion. Surface of the tested part showed macroscopically the features typical for white corrosion, and the resulting corrosion changes led to a disturbance of the alloy cohesion. The research performed have shown that the tested solenoid valve has intergranular corrosion as a reaction of the environment containing road salt. The corrosion was initiated in the areas of the alfa phase existence appearing in the eutectic areas which propagated over dendritic areas of the alloy. Initiation of the corrosion followed as a result of the galvanic effect of the alfa phase reach in aluminium showing higher electrochemical potential, in contact with the eta phase reach in zinc. The impact of the phase reach in lead present in the microstructure on the corrosion processes run was not found.
Go to article

Abstract

The mechanical properties of steel components are controlled by the chemical composition and mechanical treatment to which the steel is submitted. Non-metallic inclusions have a very high influence on the steel quality but secondary metallurgy enables to reduce their content in the steel. Possibilities of secondary metallurgy are relatively extensive but financial situation in Slovak foundries does not enable to make investments in secondary metallurgy in the near future. Accessible means for influencing of steel quality is injection of aninert gas. Main goal of experiments described in the article was verify the influence of blowing of argon into the steel in an electric induction furnace on its cleanness. Duration and flow-rate of argon blowing have a very clearly influence on the final content of non-metallic inclusions. Minimum time of argon blowing necessary for reducing of content of non-metallic inclusions in one tonne electric induction furnace was more than 6 minutes and recommended argon flow rate was 10 litters per minute.
Go to article

Abstract

The work presents results of investigations concerning the production of cast iron containing about 5-6% aluminium, with the ferritic matrix in the as-cast state and nodular or vermicular graphite precipitates. The examined cast iron came from six melts produced under the laboratory conditions. It contained aluminium in the amount of 5.15% to 6.02% (carbon in the amount of 2.41% to 2.87%, silicon in the amount of 4.50% to 5.30%, and manganese in the amount of 0.12% to 0.14%). After its treatment with cerium mixture and graphitization with ferrosilicon (75% Si), only nodular and vermicular graphite precipitates were achieved in the examined cast iron. Moreover, it is possible to achieve the alloy of pure ferritic matrix, even after the spheroidizing treatment, when both the aluminium and the silicon occur in cast iron in amounts of about 5.2÷5.3%.
Go to article

Abstract

The article presents results of research on the influence of variable parameters of horizontal continuous casting on the structure of AlCu4MgSi (EN AW-2017A) alloy ingots. The special character of the process allows for a continuous change of some of its parameters, namely, of the casting speed and of the rate of the cooling fluid flow thorough the crystallizer. These parameters have a significant impact on the crystallization process of the liquid metal. Depending on the cooling rate, intensity of the convection inside the solidifying alloy, and its chemical composition, there may arise some differences in the structure of the cast. In this study, ingots obtained at different casting speeds have been analyzed. The research methodology, based on light microscopy and electron microscopy (SEM), as well as energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD), allowed for a thorough examination of the structure of the studied materials. The results were shown that an increase in the ingot casting speed leads to an increase in the average grain surface area.
Go to article

Abstract

The paper concerns experimental work studying chemical composition, structures and selected mechanical properties of castings produced by rheocasting method SEED. After previous experiments, which showed inclusions in the primary phase α(Al) when observing structures, hypothesis of external nuclei was taken. The main goal of the work was to determine the influence of inoculation by various additions of titanium/boron based inoculant on the structure and properties of AlSi7Mg0,3 alloy. The master alloy AlTi5B1 was added in amounts of 0,05, 0,1, 0,15, 0,2 wt %. Metallographic observation by light and SEM microscopy was used for analysing the structures. Measurements of grain size were realised and evaluated. Brinell hardness measurements were performed. Chemical composition was measured by GDS analysis. Undertaken experiments did not prove the effect of inoculation of combined AlTi5B1 master alloy on castings made of AlSi7Mg0,3 alloy made by rheocasting SEED at given amounts and conditions.
Go to article

Abstract

The aim of that work was the evaluation of the quality of welded connections elements (welds) from the 30HGS steel and titanium alloy Ti6Al4V. The metallographic, factographic tests were used, and measurements of microhardness with the Vickers method. In the head weld of the 30HGS steel there were non-metallic partial division and bubbles observed. The average microhardness in the head connection was 320 HV0.1. There was no significant increase/decrease observed of microhardness in the head influence zone of the weld. There was a good condition of head connections observed, in accordance with the standard EN12517 and EN25817. In the head weld of Ti6Al4V titanium alloy there were single, occasional non-metallic interjections and bubbles observed. There were no cracks both on the weld, and on the border of the heat influence zone. The value of microhardness in head connection was in the range 300÷445 HV0.1. Reveal a very good condition of the head connections in accordance with the standard EN12517 and EN25817. The factographic tests prove the correctness of welded connections done and then heat treatment in case of steel and titanium alloy.
Go to article

This page uses 'cookies'. Learn more