Search results

Filters

  • Journals
  • Date
  • Type

Search results

Number of results: 5
items per page: 25 50 75
Sort by:

Abstract

The influence of external factors, temperature and flow velocity on the corrosion processes St3 in model solutions petrochemical plant recycled water with high salinity and hardness without open systems and in the presence of the inhibiting composition. It was found that an increase in temperature leads to a linear increase in corrosion rates, and the change in circulating water flow rate leads to the extreme nature of corrosion processes; optimal conditions are determined. Recommended use of cathodic inhibitors or mixed type inhibitor, in particular, the composition "SVOD-BI" (means for controlling the biological corrosion), which can significantly reduce the effect of temperature and flow on the corrosion rate St3, promotes the growth and strengthening of the oxide film in the presence of oxygen, increases the degree of protection of steel and preventing the formation of at its surface carbonate-calcium deposits.
Go to article

Abstract

The paper deals with possibility to improve operating performance of cast-iron heat exchangers by providing them with a copper alloy (CuTi2Cr) with the use of the flame spraying method. A test exchanger was cast of a gray cast iron with vermicular graphite in ferriticpearlitic matrix obtained in production conditions at KAW-MET Iron Foundry with the wire method used to vermicularize the material. The test samples were two plates cast in sand molds, of which one was given a flame-sprayed CuTi2Cr coat on one side. The operating performance of such model cast-iron heat exchangers, with and without CuTi2Cr coating, was tested on a set-up for determining the heat flow rate (thermal power) transferred by the heat exchanger to environment. The obtained results indicate that the value of the heat flow rate characterizing the CuTi2Cr-coated cast-iron heat exchanger was by 10% higher compared to the flow rate of heat conveyed to environment by the heat exchanger without coating.
Go to article

Abstract

The mechanical properties of steel components are controlled by the chemical composition and mechanical treatment to which the steel is submitted. Non-metallic inclusions have a very high influence on the steel quality but secondary metallurgy enables to reduce their content in the steel. Possibilities of secondary metallurgy are relatively extensive but financial situation in Slovak foundries does not enable to make investments in secondary metallurgy in the near future. Accessible means for influencing of steel quality is injection of aninert gas. Main goal of experiments described in the article was verify the influence of blowing of argon into the steel in an electric induction furnace on its cleanness. Duration and flow-rate of argon blowing have a very clearly influence on the final content of non-metallic inclusions. Minimum time of argon blowing necessary for reducing of content of non-metallic inclusions in one tonne electric induction furnace was more than 6 minutes and recommended argon flow rate was 10 litters per minute.
Go to article

Abstract

The analytical method of calculation of a withstand motion of fine-grained mixture is worked out in the vertical cylindrical sieve of vibrocentrifuge. Integration of differential equalization of motion is show out the reserved formulas for the calculation of kinematics descriptions of grain flow. The two-parameter continual model of the state of separation mixture is used in researches, as a heterogeneous continuous environment with variable specific mass (by porosity) on the thickness of movable layer of friable material. Change of specific mass on a radial coordinate in the cylindrical layer of mixture approximated by the function of degree, the coefficients of that are certain by the Aitken's method. Due to such approximation, the analytical decision of differential equalization of the grain flow, shown out with the use of two-parameter rheological dependence, in that the constituent of linear viscid resistance is complemented by the constituent of remaining internal dry friction, proportional overpressure in mixture, is built. An analytical decision is expressed as squaring that is not expressed through elementary functions in closed form, the close method of calculation of integral offers that is why, with the use of partial sum of row of degree. The results got close formulas result in that well comport with the results of numerical computer integration of squaring. Such method the continual models of grain flow on vibrosieves, it is assumed in that friable material is fully confined internal dry friction, are generalized known for, as a result of vibrodilution. The examples of calculations are considered, where influence of different factors is investigational, in particular values of rheological coefficients and change of porosity, on kinematics descriptions. It is set that calculation kinematics descriptions of grain flow substantially depend not only on the thickness of movable layer and rheological constants, and also from the concentration of grains near free surface of the mixture. Thus, worked out here a method of research of vertical grain flow in the cylindrical sieve of vibrocentrifuge can be an alternative to other methods in that for the calculation of motion of grain mixture of variable porosity conducted numerical computer integration of nonlinear differential equalizations.
Go to article

This page uses 'cookies'. Learn more