A model of bacterial filtration on fibrous filter media is developed. The single fibre efficiency as well as the efficiency of the whole filter - at the onset of the process and the evolution of those quantities - are analysed. The differences between the numerical modelling of colloidal particles and bacteria are stressed in detail. The main differences are the active motion ability of bacteria and biofilm formation. The parameters of the model were identified based on the literature data.
Pre-treatment techniques employed for exhaust emission control of compression ignition engines were found to reduce the emission levels by small percentage only, failing to meet the required emission regulations. Post-treatment technique including diesel particulate filtration, diesel oxidation catalysis and selective catalytic reduction is found to be an effective solution. While the fuel-based regeneration of diesel particulate filter leads to uncontrolled combustion affecting the durability of the filter. Development of an effective regeneration system is one of the major technical challenges faced by automotive industry for meeting emission norms. A composite regeneration system with the application of microwave energy is proposed in this paper. As an initial phase, a three-dimensional model of the system is developed and its flow analysis is carried out by considering the case of single channel flow. Simulation of the regeneration process is also done by developing a Simulink model. The results of simulation showed that an engine running continuously for a period of 24 hours would require three regenerations.
Water is a strategic material. Recycling is an important component of balancing its use. Deep-bed filtration is an inexpensive purification method and seems to be very effective in spreading water recovery. Good filter designs, such as the fibrous filter, have high separation efficiency, low resistance for the up-flowing fluid and high retention capacity. However, one of the substantial problems of this process is the biofouling of the filter. Biofouling causes clogging and greatly reduces the life of the filter. Therefore, the melt-blown technique was used for the formation of novel antibacterial fibrous filters. Such filters are made of polypropylene composites with zinc oxide and silver nanoparticles on the fiber surface. These components act as inhibitors of bacterial growth in the filter and were tested in laboratory and full scale experiments. Antibacterial/bacteriostatic tests were performed on Petri dishes with E. coli and B. subtilis. Full scale experiments were performed on natural river water, which contained abiotic particles and mutualistic bacteria. The filter performance at industrial scale conditions was measured using a particle counter, a flow cytometer and a confocal microscope. The results of the experiments indicate a significant improvement of the composite filter performance compared to the regular fibrous filter. The differences were mostly due to a reduction in the biofouling effect.
The melt cleaning is an important aspect in the production of high-quality aluminum castings. Specifically inclusions within the melt and an excessively high hydrogen content lead to defects and undesired porosity in the castings. Although it is possible to reduce the amount of hydrogen and oxidic inclusions by purge gas treatment and the use of melting salts, it is impossible to remove oxides (bifilms) created during filling of gating system. Paper deals with the effects of melt quality and the placement of a filter in the filling system on Al-7%Si-Mg alloy mechanical properties. Three different filters were used: (a) rectangular ceramic pressed filter with 3 mm thickness (b) cubical pressed ceramic filter with thickness 10 mm (c) cubical pressed ceramic filter with thickness 22 mm. The results showed that the highest tensile strength values were obtained from the filter with thickness of 22 mm. Numerical simulation analysis of the filling process showed that velocity reduction by filter is the major phenomenon affecting the mechanical properties. Another evaluated aspect during experiments was capability of filters to retain old bifilms. For this purpose multiply remelted alloy was prepared and analyzed. Results showed that filter efficiency increases with decreasing melt quality as a result of possibility to retain “old” bifilms better than small and thin “new” bifilms.
Extremely intense development of civilization requires from foundry casting technologies very high quality and not expensive castings. In the foundries, there are many treatments that allow increasing of the final properties of produced castings such as refining, modification, heat treatment, etc. One of the methods of increasing the quality of the casting by removing inclusions from the liquid alloy is filtration. The use of ceramic-carbon foam filters in filtration process is still analysed phenomenon that allows improving the final properties of castings. A modern method of research, testing and synthesis of innovative chemical compositions allows improving the properties of such filters. In the paper the evaluation of application properties of developed ceramic-carbon bonded foam filters is presented. The quality of the foam filters is evaluated by Computer Tomography and foundry trials in pouring of liquid metal in test molds. Additionally computer simulations were made to visualize the flow characteristics in the foam filter. The analysed filters are the result of the research work of Foundry Research Institute and the Institute of Ceramics and Building Materials, Refractory Materials Department in Gliwice.
Trials of cast steel filtration using two types of newly-developed foam filters in which carbon was the phase binding ceramic particles have been conducted. In one of the filters the source of carbon was flake graphite and coal-tar pitch, while in the other one graphite was replaced by a cheaper carbon precursor. The newly-developed filters are fired at 1000o C, i.e. at a much lower temperature than the currently applied ZrO2-based filters. During filtration trials the filters were subjected to the attack of a flowing metal stream having a temperature of 1650°C for 30 seconds. Characteristic of the filters’ properties before and after the filtration trial were done. It was found, that the surface reaction of the filter walls with molten metal, which resulted in local changes of the microstructure and phase composition, did not affect on expected filter lifetime and filtration did not cause secondary contamination of cast steel.
Applications of morphological filters for two-process profiles were analysed. Dilation, closing and alternating sequential (closing + opening) filters were used with a circle (disk) as a structuring element. An original method of a disk radius selection was elaborated for two-process profiles. This procedure was applied for many simulated and measured profiles. Behaviors of morphological filters were compared with those of double Gaussian (Rk) filter. Robust filter was also taken into consideration. In calculation, TalyMap software was used. The proposed procedure was found to be very useful. It was developed for 2D profiles but it can be easily extended for an areal (3D) surface topography filtering. From among morphological filters, the alternate sequential filter is suggested.
Filtration process is one of the basic and essential processes in technological systems for treatment of municipal, community and industrial wastewater treatment. Filtration process is a subject of numerous published research and theoretical elaborations. This publication concerns theoretical analysis with basic character, and is a verification of theoretical analysis and physical equations describing process of filtration aided with empirical formulas.
This paper presents the comparison of filtering methods – median filtration, moving average Kalman filtration and filtration based on a distance difference to determine the most accurate arm length for circular motion, as a model of wind turbine propellers movement. The experiments have been performed with the UWB technology system containing four anchors and a tag attached to 90cm arm that was rotated with speed up to 15.5 rad/s (as a linear speed of 50km/h). The trilateration concept based on the signal latency has been described in order to determinate the position of an object on circular trajectory. The main objective is the circle plane rotation (parallel and perpendicular) with respect to the anchors plane reference system. All research tasks have been performed for various cases of motion schemes in order to get the filtration method for object in motion under best accuracy goal. Filtration methods have been applied on one of two stages of the positioning algorithm: (1) on raw data got from the single anchor-tag (before trilateration); (2) on the position obtained from four anchors and tag (after trilateration). It has been proven that the appropriate filtering allows for higher location accuracy. Moreover, location capabilities with the use of UWB technology – shows prospective use of positioning of objects without access to other positioning forms (ex. GPS) in many aspects of life such as currently developing renewable, green energy sources like wind turbines where the circular motion plays an important role, and precise positioning of propellers is a key element in monitoring the work of the whole wind turbine.
Aerosol filtration in fibrous filters is one of the principal methods of accurate removal of particulate matter from a stream of gas. The classical theory of depth filtration of aerosol particles in fibrous structures is based on the assumption of existing single fibre efficiency, which may be used to recalculate the overall efficiency of entire filter. Using “classical theory” of filtration one may introduce some errors, leading finally to a discrepancy between theory and experiment. There are several reasons for inappropriate estimation of the single fibre efficiency: i) neglecting of shortrange interactions, ii) separation of inertial and Brownian effects, ii) perfect adhesion of particles to the fibre, iv) assumption of perfect mixing of aerosol particles in the gas stream, v) assumption of negligible effect of the presence of neighbouring fibres and vi) assumption of perpendicular orientation of homogenous fibres in the filtration structure. Generally speaking, “classical theory” of filtration was used for characterization of the steady - state filtration process (filtration in a clean filter, at the beginning of the process) without deeper investigation of the influence of the nternal structure of the filter on its performance. The aim of this review is to outline and discuss the progress of deep-bed filtration modelling from the use of simple empirical correlations to advanced techniques of Computational Fluid Dynamics and Digital Fluid Dynamics.
The mathematical model of postproduction suspension concentration by microfiltration has been developed. This model describes a process conducted in a batch system with membrane washing by reverse flow of permeate. The model considerations concern filtration pseudocycles consisting of the filtration period and the membrane washing period. The balances of continuous phase volume, dispersed phase mass and energy, for each period of pseudocycle respectively, have been presented.
Deep bed filtration is an effective method of submicron and micron particle removal from the fluid stream. There is an extensive body of literature regarding particle deposition in filters, often using the classical continuum approach. However, the approach is not convenient for studying the influence of particle deposition on filter performance (filtration efficiency, pressure drop) when non-steady state boundary conditions have to be introduced. For the purposes of this work the lattice-Boltzmann model describes fluid dynamics, while the solid particle motion is modeled by the Brownian dynamics. For aggregates the effect of their structure on displacement is taken into account. The possibility of particles rebound from the surface of collector or reentrainment of deposits to fluid stream is calculated by energy balanced oscillatory model derived from adhesion theory. The results show the evolution of filtration efficiency and pressure drop of filters with different internal structure described by the size of pores. The size of resuspended aggregates and volume distribution of deposits in filter were also analyzed. The model enables prediction of dynamic filter behavior. It can be a very useful tool for designing filter structures which optimize maximum lifetime with the acceptable values of filtration efficiency and pressure drop.
The article presents the results of studies on the efficacy of water desalination (i.e. Elimination of NaCl ions from the solution) using graphene-polyamide composite membranes. The membrane used for filtration consists of a monolayer of polycrystalline graphene on a porous polyamide carrier support (nylon 66). The degree of desalination for an aqueous NaCl solution percolated through the membrane was 18%. In the future this type of membrane may replace the currently used reverse osmosis membranes.
The situation when groundwater considerably rises above the “normal” level, water intake, lowering of groundwater levels and other relevant practical tasks require the drainage facilities. The most effective techniques of numerical studies of the corresponding boundary problems at present time are methods of dealing with inverse boundary value problems (conformal and quasi-conformal mappings). As basis of this research we used the case of combining the fictitious domain methods with quasi-conformal mappings of the solution of nonlinear boundary value problems for the calculation of filtra-tion regimes in environments with free boundary areas (depression curves) and zones of “mountainous” areas. This paper reviews the stationary issue of flat-vertical stationary non-pressure liquid filtration to horizontal symmetric drainage. In the paper a practical methodology for solving boundary value problems on conformal mappings is suggested for the calculation of the filtration process in the horizontal symmetrical drainage. The idea of block iterative methods was used during the creation of the corresponding algorithm which is based on the alternating “freeze” of the anticipated conformance parameter, the internal and boundary connections of the curvilinear area. The results of the conducted numerical calculations confirmed the effectiveness of the suggested problem formulations and algorithms of their numerical solution and the possibility of their use in the modelling of nonlinear filtration processesoccurring in horizontal drainage systems, as well as in the design of drainage facilities and optimizing other hydrosystems. Therefore these results are of great importance.
Foundry technologists use their own style of gating system designing. Most of their patterns are caused by experience. The designs differ from plant to plant and give better or worse results. This shows that the theory of gating systems is not brought into general use sufficiently and therefore not applied in practise very often. Hence, this paper describes the theory and practical development of one part of gating systems - sprue base for automated horizontal moulding lines used for iron castings. Different geometries of sprue bases with gating system and casting were drawn in Solid Edge ST9. The metal flow through the gating systems was then simulated with use of MAGMA Express 220.127.116.11, and the results were achieved. The quality of flow was considered in a few categories: splashes, air entrapment, vortex generation and air contact. The economical aspect (weight of runner) was also taken under consideration. After quantitative evaluation, the best shape was chosen and optimised in other simulations with special attention on its impact on filling velocity and mould erosion. This design (a sprue base with notch placed in drag and cope) is recommended to be used in mass production iron foundries to reduce oxide creation in liquid metal and especially to still metal stream to improve filtration.
The aim of the study was to analyze and assess the possibility of using a two-stage filtration system with ceramic membranes: a 3-tube module with 1.0 kDa cut-off (1st stage) and a one-tube module with 0.45 kDa cut-off (2nd stage) for treating effluent water from a juvenile African catfish aquaculture. The study revealed that during the 1st filtration stage of the effluent water, the highest degrees of retention were obtained with respect to: suspended solids SS (rejection coefficient RI=100%), turbidity (RI=99.40%), total iron (RI=89.20%), BOD5 (RI=76.0%), nitrite nitrogen (RI=62.30%), and CODCr (RI=41.74%). The 2nd filtration stage resulted in a lower reduction degree of the tested indicators in comparison to the 1st filtration stage. At the 2nd stage, the highest values of the rejection coefficient were noted in for the total iron content (RIV=100%), CODCr (RIV=59.52%; RV=64.28%, RVI=63.49%) and turbidity (RIV and RV = 45.0%, RVI=50.0%). The obtained results indicate that ceramic membranes (with 1.0 and 0.45 kDa cut-offs) may be used in recirculation aquaculture systems as one of the stages of effluent water treatment.
The paper presents the results of studies to determine the effect of complex surface and bulk modification and double filtration during mould pouring on the stereological parameters of macrostructure and mechanical properties of castings made from the post-production waste IN-713C and the MAR-247 nickel alloys. The evaluation covered the number of grains per 1mm2 of the sample surface area, the average area of grains and the shape index, hardness HB, tensile strength and resistance to high temperature creep. The results indicate the possibility of controlling the stereological parameters of macrostructure through application of several variants of the modification, controlling in this way also different low- and high-temperature properties. The positive effect of double filtration of the alloy during mould pouring on the metallurgical quality and mechanical properties of castings has also been emphasized.
In 2014 we finished research works involved in the development of a technology for manufacturing innovative ceramic-carbon foam filters for molten metal alloys filtration, which were financed by the National Centre for Research and Development (NCBiR) from INNOTECH programme resources. A batch of the filters produced in this technology was tested in practice in domestic cast steel and cast iron foundries. The trials were successful and foundries declared their intention to purchase the newly-developed filters for the current production of casts. This provided an incentive for “Ferro-Term” Sp. z o.o. to start design works on the prototype line for a serial production of these filters. At the same time, in co-operation with a scientific consortium, including the co-authors of the technology, i.e. the Institute of Ceramics and Building Materials, Refractory Materials Division in Gliwice, Institute for the Chemical Processing of Coal in Zabrze and Foundry Research Institute in Cracow, the company made a successful attempt to raise some funds for the necessary adaptation of the developed technology from the semi-technical to industrial scale from Intelligent Development Operational Programme. In the article we have presented information on the effects of works performed within the framework of the project entitled “Modernization and adaptation of the existing technological line for purposes related to technology verification and start-up of the production of innovative ceramic-carbon filters for molten metal alloy filtration”.
The post-processes coke wastewater treatment was carried out using flat ultrafiltration membranes with a variable polysulfone concentration in membrane solution (15 wt% - 17% wt.) and variable evaporation time of the solvent from the polymer film surface (0s, 2s, 5s). The ultrafiltration process was carried out with the transmembrane pressure of 0.4 MPa and the linear speed of water flow over the surface of the membrane at 2 m / s. For all the membranes transport characteristic of de-ionized water describing the dependence of the volumetric flow on the transmembrane pressure was done. Since none of the ultrafiltration membranes prepared had provided a sufficiently high degree of pollutants removal from wastewater, it was post-treated by RO method. The wastewater treated this way can be used as technical water for coke quenching. The calculations based on the assumptions of the hydraulic model of filtration resistance allowed to predict the efficiency of ultrafiltration membranes used in the process. To that end, for each of the membranes, the following parameters were determined experimentally: the alterations of effluent stream volume over the time of the low-pressure filtration, the total hydraulic resistance and the resistance constituents such as „new” membrane resistance, the resistance generated by polarization layer and the resistance caused by fouling - reversible and irreversible.