Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 24
items per page: 25 50 75
Sort by:

Abstract

Refined Schwarz-Christoffel (SC) conformal transformations allow us to perform reliable quantitative evaluation of the accuracy of local computation of electric and magnetic fields with limited effort, which can be useful to complement well known comparisons of global results. In this paper some examples are presented for mesh point potentials obtained by means of finite difference (FD) methods, but it is possible that similar considerations will be useful in the case of finite element methods (FEM) or meshless computations too.
Go to article

Abstract

A novel method of active noise control using adaptive radiation sound sources is investigated. A finite element model of a modal enclosed sound field is excited harmonically, representing a noise field in the low-frequency range. The control sources are comprised of elementary dipole sources for which the driving signals are adjusted by an optimization method. Two set-up cases of the proposed compound sources are investigated. The coupling of the control sources with the modal sound field is discussed. The simulated performance of the proposed method is compared with that of a system with distributed simple sources and the results show the effectiveness of the sources with adaptive radiation for active noise control in small enclosures.
Go to article

Abstract

The Tertiary lignite formations in the Bełchatów deposit, along with coal, are built of plastic, weakly compact and loose rocks. Their physical and mechanical parameters, don’t pose operational problems. However, varieties of a different lithological character and physical-mechanical properties rocks, causing difficulties when mining the overburden rocks, appear within them. These include: Mesozoic limestones, Tertiary sandstones and conglomerates, as well as Quaternary iron feldspar rocks. The article features a lithological characterization as well as values of basic physico-mechanical parameters. They form the basis of the geological engineering classification and decide about their difficult workability. The possibilities of their raw material utilization were also discussed.
Go to article

Abstract

The instability characteristics of a dielectric fluid layer heated from below under the influence of a uniform vertical alternating current (AC) electric field is analyzed for different types of electric potential (constant electric potential/ electric current), velocity (rigid/free) and temperature boundary conditions (constant temperature/heat flux or a mixed condition at the upper boundary). The resulting eigenvalue problem is solved numerically using the shooting method for various boundary conditions and the solution is also found in a simple closed form when the perturbation heat flux is zero at the boundaries. The possibility of a more precise control of electrothermal convection (ETC) through various boundary conditions is emphasized. The effect of increasing AC electric Rayleigh number is to hasten while that of Biot number is to delay the onset of ETC. The system is more stable for rigid-rigid boundaries when compared to rigid-free and least stable for free-free boundaries. The change of electric potential boundary condition at the upper boundary from constant electric potential to constant electric current is found to instill more stability on the system. Besides, increase in the AC electric Rayleigh number and the Biot number is to reduce the size of convection cells.
Go to article

Abstract

This article deals with a group of Polish surnames motivated by lexis from the field of salt mining. The analysed surnames are excerpted from “Słownik nazwisk współcześnie w Polsce używanych”, edited by Kazimierz Rymut, as well as from other onomastic compilations. These anthroponyms vary in terms of their origins and linguistic construction. We can distinguish from among these anthroponyms: 1) surnames motivated by impersonal nouns: solanka, solnica, sól, tołpa, żupa; 2) surnames motivated by adjectives: słony, solny; 3) surnames motivated by personal nouns: prasoł, solarz, solnik, warzyc, warzysz, żupnik. The description of particular ‛salt’ surnames, apart from their frequency, includes their geographical distribution, which only in some cases is connected with the location of old salt mines, found mainly in the Lesser Poland (Małopolska).
Go to article

Abstract

Analytical relations, describing the electrical fields of cylindrical piezoceramic radiators with circular polarization as a member of the cylindrical systems with the baffle in the inner cavity, using the related fields method in multiply connected regions were obtained. Comparative analysis of the results of numerical experiments performed on the frequency characteristics of the electric field of the radiating systems for different modes of radiation allow to establish a number of subtle effects of the formation of the electric field of radiators.
Go to article

Abstract

In 1949 the first book of the Atlas of Polish Traditional Costumes series appeared. Józef Gajek was the one who initiated the series, published by Polish Folk Association to this day. He was associated with Polish Ethnographic Atlas, which had a great impact on the character of the series. Its main objective was to describe Polish traditional costumes according to particular regions. Janusz Kamocki and Barbara Bazielich were subsequent editors of the series. Since 2011 the authors of this article have been part of the editorial staff. At their initiative ten more books of the series were published in the years 2013–2018, field research on traditional handicraft was conducted and the Traditional Costume Section was established. The article describes the circumstances accompanying this editorial series appearance and discusses both main directions in research on traditional costumes and activities for popularising knowledge of this unique cultural phenomenon.
Go to article

Abstract

A ship built from ferromagnetic steel disturbs the uniformity of the Earth’s magnetic field. Changes of ship’s signature are due to the magneto-mechanical interaction of the hull with the Earth’s magnetic field. The ship’s magnetic field can be detected by a magnetic naval mine. For this reason, the vessel has to be demagnetized. There are several methods of ship’s de-perming. The results of experimental and computer simulations of the ship’s de-perming process using coils lying on the seabed are presented in this paper. The simulation of the de-perming process with a hysteresis model of ship’s steel was carried out in Opera-3d 18R2. The laboratory experiments were carried out using a physical ship’s model, several Helmholtz coils, magneto-resistive sensors, etc. The experiments and computer simulations have shown that ship’s de-perming with coils lying on the seabed is possible. The values of coil currents are over dozen times greater than those used in the standard method.
Go to article

Abstract

The current research aimed to use non traditional methods to control some stored grain insects. The effects of 180 millitesla (mT) magnetic field (MF) for six different exposure periods (3 min, 30 min, 1 h, 12 h, 24 h and 48 h) on mortality (%) of two stored grain insects, Tribolium casteneum adults and Trogoderma granarium larvae, reduction in F1-progeny (%), seeds germination (%) and seed components (%) after 8 months storage period were studied under laboratory conditions. According to results, the mortality (%) of tested insects increased with increasing of MF time exposure. Trogoderma granarium was more resistant than T. casteneum in which mortality reached 56 and 75%, respectively 14 days after from exposure period. Without any negative effect on seeds germination (%) the MF was very effective in protecting stored wheat from insect infestation up to 8 months compared to non-magnetic seeds which became infested after 3 months of storage. Furthermore, the germination (%) was accelerated by 6 h compared to non-magnetic seeds. The MF level caused a slight increase in the percent of total carbohydrate, crude protein and ash while slightly decrease the percent of moisture, total fats and crude fiber.
Go to article

Abstract

For development of the knowledge-based economy, potential and quality of university education are an important factors to increase a competitiveness of local, regional, national and international scales. To shape the modern economy, the development of university education and studies corresponding with contemporary socio-economic challenges play an important role. As a result, the formation of scientific and academic centres, which are the basic elements of knowledge-based of economy, determines the improvement of the human resources quality and the increase in innovativeness of spatial systems on various scales. The author has discussed the issue of changes in university education in Poland and its role in socio-economic activation of regional systems, and also defined the structure of major studies in regional (voivodship) systems. This paper research has initiated wider investigations which aim will be to answer to what extent the actual university education structure corresponds to contemporary and future socio-economic needs and competences. this level of education in Poland has to face with the growing globalization processes and increasing spatial competitiveness, not only in a regional scale, but also in the national and international ones, and actual reforms of Polish education and science system.
Go to article

Abstract

The aim of this paper is to present methods of digitally synthesising the sound generated by vibroacoustic systems with distributed parameters. A general algorithm was developed to synthesise the sounds of selected musical instruments with an axisymmetrical shape and impact excitation, i.e., Tibetan bowls and bells. A coupled mechanical-acoustic field described by partial differential equations was discretized by using the Finite Element Method (FEM) implemented in the ANSYS package. The presented synthesis method is original due to the fact that the determination of the system response in the time domain to the pulse (impact) excitation is based on the numerical calculation of the convolution of the forcing function and impulse response of the system. This was calculated as an inverse Fourier transform of the system’s spectral transfer function. The synthesiser allows for obtaining a sound signal with the assumed, expected parameters by tuning the resonance frequencies which exist in the spectrum of the generated sound. This is accomplished, basing on the Design of Experiment (DOE) theory, by creating a meta-model which contains information on its response surfaces regarding the influence of the design parameters. The synthesis resulted in a sound pressure signal in selected points in space surrounding the instrument which is consistent with the signal generated by the actual instruments, and the results obtained can improve them.
Go to article

Abstract

The classic relationships concerning the harmonic content in the air gap field of three-phase machines are presented in form of series of rotating waves. The same approach is applied to modeling of permanent magnet motors with fractional phase windings. All main reasons of non-sinusoidal shape of flux density distribution, namely, magnets’ shape and their placement, slotting, magnetic saturation and eccentricity are also related to their counterparts in modal-frequency spectrum. The Fourier 2D spectrum of time-stepping finite element solution is confronted with results of measurements, with special attention paid to accuracy of both methods.
Go to article

Abstract

An automated procedure based on evolutionary computation and Finite Element Analysis (FEA) is proposed to synthesize the optimal distribution of nanoparticles (NPs) in multi-site injection for a Magnetic Fluid Hyperthermia (MFH) therapy. Evolution Strategy and Non dominated Sorting Genetic Algorithm (NSGA) are used as optimization procedures coupled with a Finite Element computation tool.
Go to article

Abstract

This paper presents an approximate analytical model for estimating the transmission loss (TL) of a finite rectangular plate in the low frequency range, which is based on the modal summation approach (MSA) taking into account the modal radiation impedance and fluid loading. The mode-dependent radiation resistance is calculated using the Rayleigh integral. The fluid loading is taken into account through the natural frequency modified by the added mass. The results are compared with the ones of Statistical Energy Analysis (SEA) coupled with FEM and FEM coupled with BEM. In addition, the effects of the various vibration modes and the fluid loading on TL, and a way for reducing the calculation time are discussed.
Go to article

Abstract

Ultrasonic processing in the cavitation mode is used to produce the composite materials based on the metal matrix and reinforcing particles of micro- and nano-sizes. In such a case, the deagglomeration of aggregates and the uniform distribution of particles are the expected effects. Although the particles can not only fragment in the acoustic field, they also can coagulate, coarsen and precipitate. In this paper, a theoretical study of processes of deagglomeration and coagulation of particles in the liquid metal under ultrasonic treatment is made. The influence of various parameters of ultrasound and dispersion medium on the dynamics of particles in the acoustic field is considered on the basis of the proposed mathematical model. The criterion of leading process (coagulation or deagglomeration) has been proposed. The calculated results are compared with the experimental ones known from the scientific literature.
Go to article

Abstract

As one of the key techniques in the fully mechanized mining process, equipment selection and matching has a great effect on security, production and efficiency. The selection and matching of fully mechanized mining equipment in thin coal seam are restricted by many factors. In fully mechanized mining (FMM) faced in thin coal seams (TCS), to counter the problems existing in equipment selection, such as many the parameters concerned and low automation, an expert system (ES) of equipment selection for fully mechanized mining longwall face was established. A database for the equipment selection and matching expert system in thin coal seam, fully mechanized mining face has been established. Meanwhile, a decision-making software matching the ES was developed. Based on several real world examples, the reliability and technical risks of the results from the ES was discussed. Compared with the field applications, the shearer selection from the ES is reliable. However, some small deviations existed in the hydraulic support and scraper conveyor selection. Then, the ES was further improved. As a result, equipment selection in fully mechanized mining longwall face called 4301 in the Liangshuijing coal mine was carried out by the improved ES. Equipment selection results of the interface in the improved ES is consistent with the design proposal of the 4301 FMM working face. The reliability of the improved ES can meet the requirements of the engineering. It promotes the intelligent and efficient mining of coal resources in China.
Go to article

Abstract

The paper consists the problem of developing a scientific toolkit allowing to predict the thermal state of the ingot during its formation in all elements of the casting and rolling complex, between the crystallizer of the continuous casting machine and exit from the furnace. As the toolkit for the decision making task the predictive mathematical model of the ingot temperature field is proposed. Displacement between the various elements of the CRC is accounted for by changing the boundary conditions. Mass-average enthalpy is proposed as a characteristic of ingot cross-section temperature state. The next methods of solving a number of important problems with the use of medium mass enthalpy are developed: determination of the necessary heat capacity of ingots after the continuous casting machine for direct rolling without heating; determination of the rational time of alignment of the temperature field of ingots having sufficient heat capacity for rolling after casting; determination of the total amount of heat (heat capacity) required to supply the metal for heating ingots that have insufficient amount of internal heat.
Go to article

Abstract

Maintaining railway turnout operability is crucial for ensuring railway transport safety. Electric heating of railway turnouts is a significant technical and economic issue. The classical heating is characterised by high power consumption. For this reason, research is needed to optimise the current system. This paper presents results of a numerical analysis and of experimental researches. The numerical analysis was carried out using the ANSYS software. There was conducted a numerical comparative analysis of energy loss during heating performed using two different heaters. Including the classical method and a heater thermally insulated from a rail. In the first step, heating of a working space filled with a substitute snow model was considered. The snow-covered surface area was held within the working space of the turnout. It was assumed that the snow substitute material had thermal properties approximately the same as real light snow. It was also assumed that the material is in the solid state which would not undergo a phase change. In the next step, a real snow model that included the phase change process was taken into account. The energy efficiency and heat distribution in the turnout have been analysed and compared. The experimental researches were carried out in a physical model. The results showed that the use of a contactless heater results in creating a larger area over which emitted heat affected snow in the working space. Consequently, more snow was melted around the contactless heater than the classic one. This experimental observation supported the results of the numerical analyses presented previously.
Go to article

Abstract

The main purpose of the paper is to present a method which allows taking into account the anisotropic properties of dynamo steel sheets. An additional aim is to briefly present anisotropic properties of these sheets which are caused by occurrences of some textures. In order to take into account textures occurring in dynamo sheets, a certain sheet sample is divided into elementary segments. Two matrix equations, describing changes of the magnetic field, are transformed to one non-linear algebraic equation in which the field strength components are unknown. In this transformation the flux densities assigned to individual elementary segments are replaced by functions of flux densities of easy magnetization axes of all textures occurring in the given dynamo sheet. The procedure presented in the paper allows determining one non-linear matrix equation of the magnetic field distribution; in this equation all textures occurring in a dynamo sheet are included. Information about textures occurring in typical dynamo sheets may be used in various approaches regarding the inclusion of anisotropic properties of these sheets, but above all, the presented method can be helpful in calculations of the magnetic field distribution in anisotropic dynamo sheets.
Go to article

Abstract

In the paper, methodologies for the magnetic field simulation in an axial flux permanent magnet coreless (AFPMC) motor have been proposed and discussed. Two approaches have been considered and investigated, both based on representing the 3D field distribution by superimposing axisymmetric 2D patterns. The first of studied approaches applies directly to the Biot-Savart law while the second uses a 2D axisymmetric finite element method. The selected results of magnetic field distributions and electromagnetic torque characteristics for the considered AFPMC motor have been presented and compared with results obtained using the commercial FEM package 'Maxwell'. The elaborated algorithms have been incorporated into the design routines allowing multi-parameter optimisation of the considered motor construction.
Go to article

Abstract

In the article the author discusses peculiarities of three areas of psychologists’ professional activity: conducting scientific research, educating new generations of psychologists, and having a private practice. He particularly stresses the significance of empirical testability of theories for correct and ethical assessment practice (according to Evidence-Based Assessment standard) and therapeutic practice (according to Evidence-Based Practice in Psychology standard). The author also explores the cultural immersion of psychological activity.
Go to article

Abstract

Mixed boundary-value problem for periodic baffles in acoustic medium is solved with help of the method developed earlier in electrostatics. The nice feature of the method is that the resulting matrices are relatively easy for computations and that the results satisfy exactly the energy conservation law. Illustrative numerical examples present the wave-beam steering (in the far-field) in a baffle system that may be considered as a model of one-dimensional ultrasonic transducer array.
Go to article

This page uses 'cookies'. Learn more