The paper presents an analysis of the influence of the energy generated from renewable sources on an improvement in the energy efficiency of public utility building and households. It also presents the current state of the technologies for the production of electricity from renewable sources, as well as their share in the national power supply system. The conducted analysis concerns both micro, as well as large systems generating electricity. Systems generating power from renewable sources are gaining in popularity. With an increasing awareness in the society of the beneficial influence that renewable power generating systems have on the environment, as well as the support in form of various programs offering subsidies for the construction of new systems, power generation from renewable sources is becoming increasingly popular and common. Although the renewable energy systems are still not widely considered to be a profitable solution, systems using renewable sources of energy are positively perceived and treated as a new trend in the construction of multi or single-family residential buildings. The increasing share of the renewable energy in the national power supply system significantly reduces the demand for energy produced from conventional sources. This obviously translates into a reduced consumption of primary energy, for example, fossil fuels, and, in turn, leads to the reduced exploitation of natural resources, thus contributing to the protection of the natural environment. A reduced consumption of fossil fuels also means a significant reduction in environmental pollution during their processing into electricity or heat. Actions aiming at improving energy efficiency and reducing final energy consumption are being undertaken by many countries all over the world, and by the European Union. In 2012, the European Parliament and the Council issued Directive 2012/27/EU obliging the Member States to initiate actions aiming at a reduction in the consumption of final energy by 1.5% a year. The paper presents the current status of generation of energy from renewable sources during the last 13 years. The ways for using energy from the renewable sources to improve the energy efficiency of facilities were also discussed.
In this paper the results of studies of polymeric binders on the example of the new BioCo2 binder, including the problem of its renewability, are presented. The results of structural studies (FT-IR) for the BioCo2 binder before and after crosslinking, and bending strength tests Rg u fresh and renewed cured molding sands with BioCo2 binder are discussed. The cross-linking binder and curring of moulding sand was carried out by physical agents (microwave radiation, temperature). On the basis of obtained results was shown that it is possible to restore the initial properties of the adhesive of BioCo2 binder. The initial properties of moulding sand can be achieved, after the cross-linking binders and after curing in the moulding sands with bioCo2 binder , by supplementing the moulding sand composition by the appropriate amount of water.
The energy efficiency of photovoltaic modules is one of the most important aspects in energetic and economic aspects of the project related to system installations. The efficiency of modules and the electricity produced by photovoltaic conversion in solar modules is affected by many factors, both internal, related to the module structure itself and its technical and external factors related to the energy infrastructure, which includes: cabling, inverters, climate conditions prevailing at the micro-installation location and the orientation and angle of inclination of the solar modules. The installation of photovoltaic modules should be preceded by an energy efficiency analysis, which will help to indicate the optimal solution adapted to the given conditions. The article presents a comparative analysis of the amount of energy produced under real and simulated conditions. Analyzes were made on the basis of research carried out in the Wind and Solar Energy Laboratory located at the AGH University of Science and Technology, data from solar irradiation data-bases and computer software for estimating energy resources. The study examined the correlation of the solar irradiation on the modules and the amount of electricity generated in the photovoltaic module. The electricity produced by the module was compared under real conditions and simulated based on two sources of data. The comparison and analysis of the amount of energy of the module were also made, taking simulated different angles of the module’s inclination into account.
The primary aim of this paper was to assess the development of prosumer energy sector in Poland. In the first point, the basic notions connected with prosumer energy (micro-installation, prosumer) were discussed on the basis of Law of Renewable Energy Sources of February 20, 2015 (Journal of Laws, item 478, as amended) and the main aspects of the European Union energy policy where presented in the context of the development of the prosumer energy sector. In this part of the study, numerous benefits for the Polish economy and consumers of electrical energy, connected with the expansion of prosumer energy sector, were presented. On the other hand, many obstacles which stall this sector in Poland were noticed. In the second point the most important regulations from the Law of Renewable Energy Sources of February 20, 2015 were analyzed (In the second point the most important regulations from the Law of Renewable Energy Sources of February 20, 2015 (hereinafter: the RES act) were analyzed). On the basis of this legal act, the so called “rebate system”, which is currently used in Poland to support prosumers of electrical energy, was described. Moreover, many legal and administrative simplifications implemented by the RES act were indicated. The analytical approach to the RES Act in this study resulted in the detection of many regulations in this legal act which may have an adverse impact on the development of the prosumer energy sector in Poland. In the third point, programs co-financed by the Polish government or the European Union, which financially support the purchase and installation of energy technologies using RES, were described. Statistical data connected with the prosumer energy sector in Poland was presented in the fourth point of this paper. On the basis thereof, the authors attempted to find the correlation between the number of prosumers and the share of the amount of electrical energy from renewable energy sources in gross electrical energy consumption. In the fifth point issues connected with energy technologies used in the Polish prosumer energy sector were discussed. Moreover, this point focuses on the great popularity of photovoltaic modules among Polish prosumers and results in the reluctance of Polish prosumers to install wind microturbines and small hydroelectric power plants.
In spite of technological, logistic and economic difficulties, interest in renewable energy sources in the world is consistently increasing. This trend is also observed in Poland, mainly due to the urgent need to tackle the problem of climate change, which is caused by the increasing concentration of gaseous pollutants in the atmosphere. The paper presents a short script of the issue of estimating renewable energy resources in Poland in the context of creating local low carbon economy plans at the level of municipalities/counties where RES sources should be taken into account. The author proposed an individual approach to estimate the potential of RES, taking the local conditions and the short characteristics of the small and medium companies sector in Poland into account. These companies have a great application potential to increase the share of renewable energies and to improve energy efficiency in their business. The actions, which are taken by the Ministry of Energy in the field of civil energy development, enhancing local energy security and the sustainable development of renewable energy resources support the development of energy clusters covering one district or five municipalities. In the article, the author presents data on the number of companies possessing a concession for generating electricity in RES installations in the power range from 40 kW to 200 kW. These companies can largely be the nucleus for creating a local cluster in which microgrids will be a key element.
Formation the local identity in the “thematic” Rural Renewal, The article aims to determine the main conditions for the development of rural thematic areas in the context of Rural Renewal. Against this background, the authors attempt to explain the mechanisms governing the discussed process and their effects. In view of the above, the focus was on presenting mechanisms for the development of processes that lead to the flowering of this idea (an anatomy of success – the case of the village of Sierakowo Sławieńskie) and those that slow down or completely limit this development (anatomy of failure – the case of the village of Lubcza).
The aim of the article is to discuss and assess the diversification of renewable energy sources consumption in European Union member states. The time scope covers 2005 and 2015. The data comes from Eurostat. The analysis was based on synthetic indicators – using a non-standard method. Synthetic indicators were assessed based on three simple features such as: the share of renewable energy in energy consumption in 2015, the difference between the share of renewable energy in energy consumption in 2015 and in 2005 (in percentage points), deficit/surplus in the 2020 target reached in 2015 (in percentage points). The European Union member states were divided into four diversified group in terms of renewable energy sources consumption (first class – a very high level, second class – quite a high level, third class – quite a low level, fourth class – a very low level). Then the divided groups were analyzed according to the share of renewable energy sources in the primary production of renewable energy and the consumption of individual renewable energy sources. During the research period renewable energy consumption increased in the European Union, but individual member states are characterized by a diverse situation. The type of energy used depends largely on national resources. The countries of Northern Europe are characterized by a greater share of renewable energy sources in consumption. Biomass is the most popular renewable source of energy in the European Union. Depending on the conditions of individual countries – it is agricultural and forest biomass.
The inevitability and successive implementation of the elements of the European Union (EU) energy policy and the freedom of achieving the goals left in this regard for the member states should translate into actions taking the specificity of local markets into account, in order to carry out liberalization processes in a harmonious manner. In 2016, the European Commission published a package of guidance documents “Clean Energy for All Europeans” in the perspective of 2030, also known as the Winter Package. The recommendations contained in some of the documents assume the continuation of integration of markets in the national and regional dimension, setting ambitious targets in the field of decarbonization, the increase of energy efficiency and the increase of Renewable Energy Sources (RES) share in the energy balance of EU countries. The short time to carry out a thorough reconstruction of the energy-generating sector forces to seek solutions that are in line with the European Community recommendations and, at the same time, do not constitute an excessive burden for the national economy and legal order. One of the activities is to use the potential of micro-networks of local communities striving for energy independence based on their own energy sources and to create regulations enabling the neighborly exchange of energy. This mechanism works in the form of pilot projects in many locations around the world (Sonnen Group; Power Ledger). The paper presents the concept of functional and analytical assumptions for an exemplary structure of neighboring prosumers along with the presentation of simulation results based on real generation and consumption profiles and the presentation of investment profitability indicators for the proposed functional model.
Wood pellets are classified as a solid biomass type. They are one of the most popular bio-heating fuels used in Europe, especially in the small heating sector, where pellets are burned in low-power domestic boilers. The pellets and automatic pellet-fired heating devices gained popularity due to the increasing air pollution (smog) problem and the low emission limiting campaigns associated with it. Wood pellets are formed as a result of small forestry particles mechanical compression (mainly conifers originated) and they are listed among renewable energy sources. The purpose of the presented studies was to compare the quality of wood pellets used for pellet-fired boilers and to identify, qualitatively and quantitatively, impurities marked in the samples obtained from the domestic market. The application of petrographic analyses, applied so far in relation to fossil fuels, is a presented work innovation for wood pellets. The microscopic analyses were performed on both certified (ENplus/DINplus) and uncertified wood pellets available on the market. Unfortunately, the analysis revealed that the quality requirements were not met, because of the unacceptable contamination presence. The unacceptable organic inclusions in the analyzed samples are fossil coals and their derivatives, coke, and polymeric materials of natural origin. Unacceptable inorganic inclusions determined in the analyzed samples were: glass, slag, rust, pieces of metal, stone powder, plastic, and polymeric materials of inorganic origin.
The large variability and unpredictability of energy production from photovoltaic power microinstallations results from the dependence on the current weather conditions. These conditions depend on a number of factors and are variable over the time. Despite this specificity, photovoltaic micro-installations are becoming more and more popular in the world and in Poland. This is mainly due to the fact that the generation of energy from renewable sources has numerous advantages, the energy is free, renewable in time and ecological, and its production on its own gives partial independence from energy supplies from the power grid. In addition, the observed significant prices decrease of solar modules has further accelerated the development of the use of this energy source. Concern for this method of energy production among households has increased significantly in Poland after introducing the prosumer in the legal framework and the use of administrative and financial support. The implemented prosumer mechanisms allowed, for example, the net balancing of the energy consumed and produced by the micro-installation through storage in the power grid. The article describes the problem of balancing sources using solar energy, based on micro-installation used in the household (the so-called prosumer installation). The conducted analyses compared the load profile of a typical household and the energy generation profile from a photovoltaic installation, determining the real balancing formation level of such a system.
The Polish energy sector is, to a large extent, based on fossil fuels used in conventional energy, which is not entirely consistent with the current energy policy of the European Union. Therefore, it is necessary to increase the use of renewable energy sources that guarantee the preservation of the value of the natural environment in rural areas. It should be emphasized that in addition to the economic effect, the environmental effect is very important, understood as the impact of renewable energy on the natural environment and the quality of life of rural residents. The intensive development of RES raises a lot of controversy among politicians, as well as among rural residents, who are also associated with the myths regarding renewable energy as harmful to the natural environment. Rural development should be connected with the socio-economic situation, and even more so with the socio-cultural situation of its inhabitants, because it assumes that the development of rural areas in Poland is associated not only with agriculture, but also with historical and natural values and their durability. The aim of this work is to determine the attitudes of the inhabitants of rural areas of the Podkarpackie Province on the impact of renewable energy sources on the natural environment. The work assumes that the durability of rural areas is largely connected with the ability to preserve their natural values, as well as ensuring a satisfactory quality of life for residents. The basic source of data was surveys carried out in 2017 among 282 inhabitants of the Podkarpackie Province .
The implementation of micro scale combined heat and power systems is one of the ways to improve the energy security of consumers. In fact, there are many available large and medium scale cogeneration units, which operate according to the Rankine Cycle. Due to European Union demands in the field of using renewable energy sources and increasing energy efficiency result in the importance of additionally developing systems dedicated for use in residential buildings, farms, schools and other facilities. This paper shows the concept of introducing thermoelectric generators into typical wood stoves: steel plate wood stoves and accumulative wood stoves. Electricity generated in thermoelectric generators (there were studies on both three market available units and a prototypical unit developed by the authors) may be firstly consumed by the system (to power controller, actuators, fans, pumps, etc.). Additional power (if available) may be stored in batteries and then used to power home appliances (light, small electronics and others). It should be noted that commercially available thermoelectric generators are not matched for domestic heating devices – the main problems are connected with an insufficient heat flux transmitted from the stove to the hot side of the generator (caused e.g. by the non -homogeneous temperature distribution of the surface and bad contact between the stove and the generator) and inefficient cooling. To ensure the high efficiency of micro cogeneration systems, developing a dedicated construction both of the generator and the heat source is necessary.
The article discusses the importance of small hydro power plants in the Polish power system and defines the legal conditions for the operation of small hydro power plants. The phenomena occurring in the hydrological system of small hydro power plants and their impact on the natural environment were analyzed. An analysis of phenomena occurring in the hydrological system and the activity of small hydro power plants that are operating on the Radunia River helped us identify relations between different types of power plants working in cascades and possibilities of power generation control in period of several days. The above-mentioned analysis has been used in the development of a mathematical model of a hydroelectric plant and cascades of hydroelectric plants. The numerical simulations carried out concerned both the self-operating power plant and a cascade of two identical objects of this type. There is a possibility for small hydro power plant to run as a base load power plant and during periods of high demand as well (peak demand or unexpected loss of generation in the power system). A single hydroelectric power plant can deal with varying peak load demands while adding a second stage increase those abilities. A cascade of reservoir hydropower plants has a much greater ability to store energy and give it back in time. In addition, the existence of a second power plant equipped with a surge reservoir allows for a significant reduction in the amplitude of flows in the river below the cascade, which will reduce the negative impact of the cascade on the environment.
Pollution, climate change and energy security are significant problems. Climate-disrupting fossil fuels are being replaced by clean and non-depletable sources of energy. It requires major changes to energy infrastructures and strong support for promotion of the use of energy from renewable sources. Renewable energy is emerging as a driver of inclusive economic growth and reinforcing energy security. Public entities have to promote renewable energy development by implementing cost-effective national support schemes. By acting at national-level, several barriers to public and private investments could be tackled, addressing the lack of coordination between various authorising bodies at national level and stimulatng the administrative capacity to implement energy projects. It should be effective in promoting transparency for investors and others economic operators. In Poland there is a lack of regulatory policies creating incentives for decentralised energy. Market-based support schemes are still needed for small-scale self-consumption system. Currently operating solutions have been shown in the contrast of the ones applied abroad. The development of clean energy technologies depends on many factors. The author identified few most important ones, mainly financial, regulatory issues, social, environmental and characterized them in this work. The article presents the recommendations of regulatory framework and some proposals for energy cluster based policy’s tools, the introduction of which would significantly facilitate the wider renewable energy uses in Poland.
Using renewable energy sources for electricity production is based on the processing of primary energy occurring in the form of sun, wind etc., into electrical energy. Economic viability using those sources in small power plants strongly depends on the support system, based mainly on financial instruments. Micro-installations, by using special instruments dedicated to the prosumer market may become more and more interesting not only in terms of environmental energy, but also financial independence. In the paper, the term hybrid power plant is understood to mean a production unit generating electricity or electricity and heat in the process of energy production, in which two or more renewable energy sources or energy sources other than renewable sources are used. The combination of the two energy sources is to their mutual complementarity, to ensure the continuity of the electricity supply. The ideal situation would be if both sources of energy included in the hybrid power plant continuously covered the total demand for energy consumers. Unfortunately, due to the short-term and long-term variability of weather conditions, such a balance is unattainable. The paper assesses the possibility of balancing the hybrid power plant in daily and monthly periods. Basic types of power plants and hybrid components and system support micro-installations were characterized. The support system is based particularly on a system of feed-in tariffs and the possibility of obtaining a preferential loan with a subsidy (redemption of part of the loan size). Then, an analysis of energy and economic efficiency for a standard set of hybrid micro-installations consisting of a wind turbine and photovoltaic panels with a total power of 5 kW, were presented. Fourteen variants of financing, economic efficiency compared with the use of the method of the simple payback period were assumed.
The article presents selected issues from the Polish Energy Policy draft until 2040. From many issues, the authors chose the ones they considered the most revolutionary. Firstly, the National Power System should be restructured to meet the challenges of a changing environment, be adapted to the growing demand for electricity, and at the same time have the least impact on the natural environment. These goals can be achieved through reforms to reduce the importance of coal in the energy mix and the development of renewable energy sources, especially offshore wind energy. The next tasks are the development of electromobility, enabling the reduction of pollution caused by transport, and, in the longer term, after 2030, the development of nuclear energy in place of the withdrawn coal power.
Hybrid Renewable Energy Systems connected to the traditional power suppliers are an interesting technological solution in the field of energy engineering and the integration of renewable systems with other energy systems can significantly increase in energy reliability. In this paper, an analysis and optimization of the hybrid energy system, which uses photovoltaic modules and wind turbines components connected to the grid, is presented. The system components are optimized using two objectives criteria: economic and environmental. The optimization has been performed based on the experimental data acquired for the whole year. Results showed the optimal configuration for the hybrid system based on economical objective, that presents the best compromise between the number of components and total efficiency. This achieved the lowest cost of energy but with relatively high CO2 emissions, while environmental objective results with lower CO2 emissions and higher cost of energy and presents the best compromise between the number of components and system net present cost. It has been shown that a hybrid system can be optimized in such a way that CO2 emission is maximally reduced and – separately – in terms of reducing the cost. However, the study shows that these two criteria cannot be optimized at the same time. Reducing the system cost increase CO2 emission and enhancing ecological effect makes the system cost larger. However, depends on strategies, a balance between different optimization criteria can be found. Regardless of the strategy used economic criteria – which also indirect takes environmental aspects as a cost of penalties – should be considered as a major criterion of optimization while the other objectives including environmental objectives are less important.
This article, as far as possible based on the available literature, empirical measurements, and data from mesoscale models describes and compares expected wind conditions within the Baltic Sea area. This article refers to aspects related to the design and assessment of wind farm wind resources, based on the author’s previous experience related to onshore wind energy. The consecutive chapters of this publication are going to describe the present state and the presumptions relating to the development of wind energy within the Baltic Sea area. Subsequently, the potential of the sea was assessed using mesoscale models and empirical data from the Fino 2 mast that is located approximately 200 kilometers away from the majority of areas indicated in the Polish marine spatial development plan draft of Poland for offshore wind farm development (Maritime Office in Gdynia 2018). In the chapter describing mesoscale models, the author focused his attention on the GEOS5.12.4 model as the source of Modern-Era Retrospective Analysis for Research and Application 2 data, also known as MERRA2 (Administration National Aeronautics and Space Agency, 28), which, starting from February 2016, replaced MERRA data (Thogersen et al. 2016) and have gained a wide scope of applications in the assessment of pre-investment and operational productivity due to a remarkable level of correlation with in-situ data. Model-specific data has been obtained for eight locations, which largely overlap with the locations of the currently existing offshore wind farms within the Baltic Sea area. A significant part of this publication is going to be devoted to the description of the previously mentioned Fino 2 mast and to the analysis of data recorded until the end of 2014 by using the said mast (Federal Maritime and Hydrographic Agency 2018). The analysis has been carried out by means using scripts made in the VBA programming language, making it easier to work with large chunks of data. Measurements from the Fino 2 mast, together with long-term mesoscale model-specific measurements can be used, to some extent, for the preliminary assessment of wind farm energy yield in the areas designated for the development of renewable energy in the Polish exclusive maritime economic zone (Maritime Office in Gdynia 2018). In the final part of this article, pieces of information on the forecasted Baltic Sea wind conditions, especially within the exclusive economic zone of Poland, are going to be summarized. A major focus is going to be put on the differences between offshore and onshore wind energy sources, as well as on further aspects, which should be examined in order to optimize the offshore wind power development.
The condition of the Polish energy sector does not inspire any trust of its customers. Outdated machinery and the lack of investment in new technologies make it necessary to take action to ensure the stability and continuity of electricity supplies to the end-user. In Poland, the industrial power sector is based on the use of coal and despite the Government’s announcements to resign from this raw material, more and more power investments are being made to generate energy from coal (Ostrołęka power plant). The solution which compensates for the current state of the Polish power industry is the development of distributed generation. The article presents a description of dispersed sources, power market, its organization and problems arising from its implementation. Distributed energy sources in the form of micro installations, energy clusters and virtual power plants have been described and characterized as well. It also assesses the impact of power market introduction on the development of distributed energy sources. The impact of the power market on the development of distributed sources is very hard to predict and determine. The functioning and further development of the energy sector, including the capacity market, strongly depends on the laws, regulations, as well as the economic and political situation in Poland and Europe. The social factor will also play an important role as the introduction of the capacity market will burden the financial side of each energy consumer. On the basis of the data presented on particular sources and distributed systems, one can only make predictions related to the possible effects of introducing the capacity market for the development of distributed sources.