This study shows the results of the investigation of the strength performance, and residual strength of a single component inorganic binder system Cast Clean S27®. The study was conducted using three different foundry sand sources in South Africa. Sample A is an alluvial coastal sample, sample B is an alluvial riverbed sample and Sample C is a blasted sample from a consolidated quartzite rock. The binder was also cured using three different curing mechanisms. The aim of the investigation was to determine the variation of strength performance and residual strength between the different South African sand sources based upon the physical and chemical properties of the sand sources. The moulding sand was prepared using three possible curing mechanisms which are carbon dioxide curing, ester curing and heat curing. The strength measurements were determined by bending strength. Sample A and sample C sand had good strength development. Sample B sand had inferior strength development and excellent high temperature residual strength. The study showed that the single component inorganic binders have good strength development and low residual strength. The silica sand properties have major contributing factors on both strength development and residual strength. The degree of influence of silica sand properties on strength performance and residual strength is dependent on the time of curing and method of curing.
One of the purposes of the application of chemically modified inorganic binders is to improve knocking out properties and the related reclamability with previously used in foundry inorganic binder (water glass), which allowing the use of ecological binders for casting nonferrous metals. Good knocking out properties of the sands is directly related to the waste sands reclamability, which is a necessary condition of effective waste management. Reclamation of moulding and core sands is a fundamental and effective way to manage waste on site at the foundry, in accordance with the Environmental Guidelines. Therefore, studies of reclamation of waste moulding and core sands with new types of inorganic binders (developed within the framework of the project) were carried out. These studies allowed to determine the degree of recovery of useful, material, what the reclaimed sand is, and the degree of its use in the production process. The article presents these results of investigation. They are a part of broader research programme executed under the project POIG.01.01.02-00- 015/09 "Advanced materials and technologies".
Mechanization of the process of core making with the use of inorganic and organic binders is based, almost solely, on core blowing machines. Presently the core blowing machines are equipped with tools and devices that allow for application of different technologies of core making. Cold-box, hot-box and warm-air technologies require that core blowing machines shall be additionally equipped with either core-box pre-heating system or gas purging and neutralization system, or hot air purging systems. Considering the possibility of using varied, the most advantageous technologies of core making, the production of universal core blowing machines equipped with replaceable devices has been undertaken in Poland. The universal core blowing systems allow for mechanization of core making process also with the use of sand, bonded by modern, eco-friendly binder systems. The paper presents selected results-based evaluation of core blowing process showing the scope of conducted design and implementation works.
One of the factors that contribute to the development of foundry moulding technology is environmental protection. The related challenges are effectively satisfied by a new inorganic binder that has been designed for castings made of non-ferrous metal alloys. This article presents in a concise way the test results, showing the ecological character of the new binder at the stage of making moulds, pouring them with metal and cooling of castings, indicating the possibilities for an economic re-use of waste materials formed during practical application of this technology. The results were compared with the results obtained on the sands with organic binders. Studies were carried out under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies."
This paper presents the results of research which is part of studies carried out under the project POIG.01.01.02-00-015/09 "Advanced Materials and Technologies", one of the aims of which is to introduce new, environment-friendly, inorganic binders to the production of castings from non-ferrous metals. The paper presents the results of research on the management of waste moulding sands prepared according to the new technology, including their multiple reclamation and management of post-reclamation waste. Studies of multiple reclamation are a continuation of the preliminary research described earlier. The programme of the studies described in this paper also included validation of the results under industrial conditions.
The development of economy and industry introducing new technologies and materials often means the increased threat of occurrence of factors harmful to humans and environment. Workers employed in foundries as mould pourers are the group of high professional risk. Foundry moulding sands when poured with liquid metal are a source of the emission of harmful, toxic and carcinogenic (benzene, PAHs) compounds. The paper presents the results of studies on the concentration of chemical compounds emitted in the process of casting aluminium alloy and brass using moulding sands with the new inorganic binders. The specific values of the exposure indices were compared with the limit values. This enabled an assessment of the impact of moulding sands on work environment. The obtained results were compared with the values of contaminants emitted when pouring foundry moulds made from furan sands and bentonite sands with an addition of coal dust. Studies were carried out under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies."