Analysis of the use of the Russian materials (liquid glass and softening additives) has been made in accordance with the modern requirements for use in the technological processes of casting as binding materials in the production of large-sized steel railway casting. The reasons for poor knockout of liquid glass mixtures have been investigated. A complex action softening additive has been recommended for a better knocking-out ability. This solution provides a softening effect at the points of maximum formation of the liquid glass matrix strength in the processes of polymorphic transformation of the material under the influence of elevated temperatures as the result of filling the mold cavity by the melt. It has been shown that the use of additives of complex action leads to the decrease in the specific work of the knockout by four – seven times depending on the composition of the mixture and the design features of the casting. Experimental-industrial tests of the proposed method for softening the liquid glass mixtures have been made and the "Front Buffer Stop" casting has been made (for the rolling stock of locomotives and railway wagons). The tests confirmed the effectiveness and expediency of implementation of new liquid glass mixtures with softening additives in conditions of foundry enterprises.
Mechanization of the process of core making with the use of inorganic and organic binders is based, almost solely, on core blowing machines. Presently the core blowing machines are equipped with tools and devices that allow for application of different technologies of core making. Cold-box, hot-box and warm-air technologies require that core blowing machines shall be additionally equipped with either core-box pre-heating system or gas purging and neutralization system, or hot air purging systems. Considering the possibility of using varied, the most advantageous technologies of core making, the production of universal core blowing machines equipped with replaceable devices has been undertaken in Poland. The universal core blowing systems allow for mechanization of core making process also with the use of sand, bonded by modern, eco-friendly binder systems. The paper presents selected results-based evaluation of core blowing process showing the scope of conducted design and implementation works.
In this study, rubber seed/shea butter oil was used to formulate core oil. The formulated core oil was characterised. D-optimal mixture design was used for multi response optimisation of the functional properties of rubber seed-shea butter coil oil. Desirable values for some responses might be obtained from a factor combination while for others responses not so desirable values. Through multiple response optimisations, a factor setting that gives the desirable values for all responses was obtained. The selected optimum mixture setting for the formulated core oil is 65.937% Rubber seed and 34.063% Shea butter oil at desirability of 0.924. Under the optimum condition the functional properties of the core oil was found to be 39.57KN/M2, 626.85KN/M2, 36.63KN/M2, 593.906KN/M2, 412.605 and 167.309s for Green Compressive Strength, Dry Compressive Strength, Green Tensile Strength, Dry Tensile Strength, Permeability and Collapsibility respectively. The optimum conditions were validated with less than 0.2% error. The functional properties of the formulated core oil was compared to the functional properties of linseed core oil. It was found that rubber seed-shea butter core oil can be used for producing cores suitable for Aluminium casting.
Skeleton castings macrostructure can be shaped in many ways, by choosing an appropriate material of cores and manufacturing technologies. Important factor, which puts foundry techniques over the other technologies of periodic cellular materials, is ability to adjust mechanical properties by changing the microstructure of an alloy from which the casting is made. The influence on the microstructure of the skeleton casting can be implemented by choosing the thermal properties, mainly thermal conductivity factor, of mould and core materials. Macro- and microstructure of skeleton castings with octahedron elementary cells was presented in this paper. The analysis concerns the differences in morphology of eutectic silicone depending on the location of measurements cross sections areas. The use of thermo-insulating material with appropriate properties assures correct fill of mould cavity and homogeneous microstructure on whole volume of skeleton casting. The selection of technological parameters of the casting process if very important as well.
The aim of this study is to demonstrate the possibility of using moulds made from the environmentally friendly sands with hydrated sodium silicate in modified ablation casting. The ablation casting technology is primarily intended for castings with diversified wall thickness and complex shapes made in sand moulds. The article presents the effect of binder content and hardening time on the bending strength Rg u of moulding sands with binders based on hydrated sodium silicate hardened by microwave technology. The aim of the research was to develop an optimal sand composition that would provide the strength necessary to make a mould capable of withstanding the modified ablation casting process. At the same time, the sand composition should guarantee the susceptibility of the mould to the destructive action of the ablation medium, which in this case is water. Tests have shown that microwave hardening provides satisfactory moulds’ strength properties even at a low binder content in the sand mixture.