In this paper results of microstructural observations for series of CuZn39Pb2 alloys produced from qualified scraps are presented. The individual alloy melts were differentiated in terms of thermal parameters of continuous casting as well as refining methods and modifications. Structural observations performed by SEM and TEM revealed formation of different types of intermetallic phases including “hard particles”. EDS results show that “hard particles” are enrich in silicon, phosphorus, iron, chromium and nickel elements. Additionally, formation of Al-Fe-Si and Al-Cr in alloy melts was observed as well. It was found that quantity and morphology of intermetallic phases strongly depends upon the chemical composition of raw materials, process parameters, modifiers and refining procedure applied during casting. It was observed that refining process results in very effective refinement of intermetallic phases, whereas modifiers, particularly carbon-based, results in formation of large particles in the microstructure.
The suspension of the copper droplets in the post-processing slag taken directly from the KGHM-Polska Miedź S.A. Factory (from the direct-to-blister technology as performed in the flash furnace) was subjected to the special treatment with the use of the one of the typical industrial reagent and with the complex reagent newly patented by the authors. This treatment was performed in the BOLMET S.A. Company in the semi-industrial conditions. The result of the CaCO3, and Na2CO3 chemicals influence on the coagulation and subsequent sedimentation of copper droplets on the crucible bottom were subjected to comparison with the sedimentation forced by the mentioned complex reagent. The industrial chemicals promoted the agglomeration of copper droplets but the coagulation was arrested / blocked by the formation of the lead envelope. Therefore, buoyancy force forced the motion of the partially coagulated copper droplets towards the liquid slag surface rather than sedimentation on the crucible bottom. On the other hand, the complex reagent was able to influence the mechanical equilibrium between copper droplets and some particles of the liquid slag as well as improve the slag viscosity. Finally, the copper droplets coagulated successfully and generally, were subjected to a settlement on the crucible bottom as desired / requested.
The copper droplets contained in the post-processing liquid slag are subjected to the treatment by the complex reagent. The complex reagent has been recently elaborated and patented in frame of the Grant No. PBS3/A5/45/2015. In particular, the complex reagent is dedicated to the post-processing slags coming from the Smelter and Refinery Plant, Głogów, as a product of the direct-to-blister technology performed in the flash furnace. The recently patented complex reagent effectively assists not only in agglomeration, and coagulation but also in the deposition of the copper droplets at the bottom of crucible / furnace as well. The treatment of the postprocessing slags by the complex reagent was performed in the BOLMET S.A. Company as in the industrial conditions which were similar to those usually applied in the KGHM – Polish Copper (Smelter and Refinery Plant, Głogów). The competition between buoyancy force and gravity is studied from the viewpoint of the required deposition of coagulated copper droplets. The applied complex reagent improves sufficiently the surface free energy of the copper droplets. In the result, the mechanical equilibrium between coagulated copper droplets and surrounding liquid slag is properly modified. Finally, sufficiently large copper droplets are subjected to a settlement on the crucible / furnace bottom according to the requirements.
Trial series of cast alloy MO59 obtained from qualified scrap was investigated. SEM and TEM of resulting precipitates were conducted. The SEM analysis demonstrated the dependence of silicon, phosphorus, iron, chromium and nickel in the composition of the so-called hard precipitates. TEM analysis showed the formation of phase AlFeSi and AlCr. Made studies have shown the important role of the composition of the batch melts brass CuZn39Pb2 type. The analysis of SEM and TEM resulting precipitates pointed to the formation of various forms of divisions, only one of which was described in the literature character of the so-called hard inclusions. The SEM studies demonstrated the dependence of the occurrence of inclusions rich in silicon, phosphorus, iron, chromium and nickel. In contrast, additional TEM analysis indicated the formation of AlFeSi phase type and AlCr. The results of the analyses referred to the structure of the batch. Due to the difficulty of obtaining recycled materials that do not contain these elements necessary to carry out further analyzes in the direction of defining the role of phosphorus in the formation of the so-called hard inclusions.
This article discusses issues related to continuous casting of brass. The tested material was CuZn39Pb2 brass with the use of continuous casting and different parameters of the process. The position consists of a melting furnace with a graphite refining pot of about 4000 cm3 chuting capacity, a graphite crystallizer of 9,5 mm nominal diameter, a primary and secondary cooling system and an extracting system as well. The analysis was carried out in terms of technological parameters of the process and type of charge. Highlighted: feedrate ingot, number of stops, and technological temperatures. The surface quality of the obtained ingots and the structure were analyzed. The most favorable conditions were indicated and technological recommendations indicated. They have been distinguished for ingots for plasticity and other technologies. Favorable casting conditions are low feed and low temperature. Due to the presence of impurities coming from the charge it is disadvantageous to have Ni greater than 0.053% by mass, and Fe more than 0.075% by mass. It is recommended to maintain a high zinc content in the melt which is associated with non-overheating of the metal during casting and earlier melting.