Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 19
items per page: 25 50 75
Sort by:

Abstract

The number of human cases of salmonellosis in the EU was 94,625 in 2015. Considering the source of these infections, Salmonella spp. was most frequently detected in broiler chicken meat and Salmonella Enteritidis (SE) was the most commonly reported serovar. The efficacy of probiotics in limiting Salmonella spp. infection in poultry has been demonstrated in numerous papers. The administration of probiotics at the level of primary production reduces the risk of contamination of poultry food products with Salmonella spp. A study was carried out in order to determine the potential for reducing the Salmonella spp. population in broiler chickens with the use of the Lavipan (JHJ, Poland) probiotic that comprised selected stains of lactic acid bacteria and Saccharomyces cervisae. Salmonella spp.-free broiler chickens were divided into two groups and received the same feed with (group L) or without (group C) the probiotic throughout the experiment. All day-old chickens were infected per os with SE. Samples of cecum content were collected 2, 4, and 6 weeks after SE infection and pectoral muscles were collected 6 weeks following SE infection for the evaluation of the SE population number. Serum samples for serological examinations were collected 6 weeks after infection. Six weeks after infection, the number of SE-positive cecal samples was lower in the L group (12.5% positive) in comparison to the C group (87.5%). Similar results were demonstrated for the muscle samples (25% in contrast to 87.5%). At the same time, in both cases, the SE CFU/g was significantly lower in the L group. The results of our study indicate that Lavipan was capable of reducing the population of SE in the gastrointestinal tract, which eventually improved the hygienic parameters of the pectoral muscles. Four weeks after infection, SE was not detected in any of the experimental groups. In both groups, no specific anti-SE antibodies were detected.
Go to article

Abstract

This article presents the research results on impact of the method of polycrystalline graphene layers separation from the growth substrate on the obtained carbon material quality. The studies were carried out on graphene sheets obtained by metallurgical method on a liquid metal substrate (HSMG® graphene). The graphene was separated using chemical etching method or the electrochemical delamination method, by separating by means of electrolysis. During electrolysis, hydrogen is emitted on a graphene-covered of cathode (metal growth substrate) as a result of the voltage applied. The graphene layer breaks away from metallic substrate by gas accumulation between them. The results from these separation processes were evaluated by means of different tools, such as SEM, TEM and AFM microscopy as well as Raman Spectroscopy. In summary, the majority of analyses indicate that the graphene obtained as a result of hydrogen delamination possesses higher purity, smaller size and number of defects, its surface is smooth and less developed after the transfer process to the target substrate.
Go to article

Abstract

The use of shredded tyre in civil engineering applications is a significant potential end use market. The reuse of tyre chips may not only address growing environmental and economic concerns, but also help to solve geotechnical problems associated with low shear strength. The purpose of this paper is to investigate the properties of tyre chips and tyre chips – sand mixture, and to find the mixture with the highest shear strength. In this study, an experimental testing program was undertaken using a large – scale triaxial apparatus with the goal of evaluating the optimum percentage of tyre chips in sand. The effects on shear strength of varying percentage of tyre chips and varying confining pressure were studied. Tyre chips content was suspected to have influence on stress – strain and volumetric strain behaviour of the mixture. Some tests were conducted to check the influence of number of used membranes, of saturation and compaction, on sample properties.
Go to article

Abstract

This paper shows results of researches of a structure and mechanical properties of metal sheets of IF steels subjected torecrystallization annealing. The annealing was held in the scope of the temperature of 600-900°C over 25 min time. The impact of heat treatment on changes of properties and structure of the researches steel has been analysed. During annealing typical processes of rebuilding of the structure deformed as a result of cold deformation in the form of forming new recrystallized grains and their growth were observed. As the temperature of annealing increases the hardness of the material gradually decreases.
Go to article

Abstract

This research paper shows the influence of a repeated SPD (Severe Plastic Deformation) plastic forming with the DRECE technique (Dual Rolls Equal Channel Extrusion) on hardening of low carbon IF steel. The influence of number of passes through the device on change of mechanical properties, such as tensile strength TS and yield stress YS, of tested steel was tested. The developed method is based on equal channel extrusion with dual rolls and uses a repeated plastic forming to refinement of structure and improve mechanical properties of metal bands [1-2]. For the tested steel the increase of strength properties after the DRECE process was confirmed after the first pass in relation to the initial material. The biggest strain hardening is observed after the fourth pass.
Go to article

Abstract

In this work, vacuum hot pressed Ni-Mn-Sn-In Heusler alloys with different concentration of In (0, 2 and 4 at.%), were investigated. The magneto-structural behaviour and microstructure dependencies on chemical composition and on heat treatment were examined. It was found that the martensite start transformation temperature increases with growing In content and to a lesser extent with increasing temperature of heat treatment. The high energy X-ray synchrotron radiation results, demonstrated that both chemical composition as well as temperature of heat treatment slightly modified the crystal structures of the studied alloys. Microstructural investigation performed by transmission electron microscopy confirmed chemical composition and crystal structure changes in the alloys.
Go to article

Abstract

The article presents the results of studies on the efficacy of water desalination (i.e. Elimination of NaCl ions from the solution) using graphene-polyamide composite membranes. The membrane used for filtration consists of a monolayer of polycrystalline graphene on a porous polyamide carrier support (nylon 66). The degree of desalination for an aqueous NaCl solution percolated through the membrane was 18%. In the future this type of membrane may replace the currently used reverse osmosis membranes.
Go to article

Abstract

Strained layer InGaAs/GaAs SCH SQW (Separate Confinement Heterostructure Single Quantum Well) lasers were grown by Molecular Beam Epitaxy (MBE). Highly reliable CW (continuous wave) 980-nm, broad contact, pump lasers were fabricated in stripe geometry using Schottky isolation and ridge waveguide construction. Threshold current densities of the order of Jth ≈ 280 A/cm2 (for the resonator length L = 700 um) and differential efficiency η= 0.40 W/A (41%) from one mirror were obtained. The record wall-plug efficiency for AR/HR coated devices was equal to 54%. Theoretical estimations of above parameters, obtained by numerical modelling of devices were Jth ≈ 210 A/cm and η = 0.47 W/A from one mirror, respectively. Degradation studies revealed that uncoated and AR/HR coated devices did not show any appreciable degradation after 1500 hrs of CW operation at 35oC heat sink temperature at the constant optical power (50 mW) conditions.
Go to article

This page uses 'cookies'. Learn more