In this paper small punch test (SPT) which is one of miniaturized samples technique, was employed to characterize the mechanical properties of carbon steel P110. The tests were carried out in the range of –175°C to RT. Results obtained for SPT were compared to those calculated for tensile and Charpy impact test. Based on tensile and SPT parameters numerical model was prepared. 8 mm in diameter and 0.8 mm in height (t) discs with and without notch were employed in this research. The specimens had different depth notch (a) in the range of 0.1 to 0.4 mm. It was estimated that α factor for comparison of Tsp and DBTT for carbon steel P110 is 0.55 and the linear relation is DBTT = 0.55TSPT. The numerical model fit with force – deflection curve of SPT. If the factor of notch depth and samples thickness is higher than 0.3 the fracture mode is transformed from ductile to brittle at –150°C.
A series of nanocomposite graphene/CoFe2O4 and graphene/NiFe2O4 hybrid materials was synthesized via facile, one-pot solvothermal route. The materials were obtained using two pressure methods: synthesis in the autoclave and synthesis in the microwave solvothermal reactor. The use of a microwave reactor enabled to significantly shorten the synthesis time up to 15 min. All the syntheses were carried out in a solution of ethanol. The effect of processing conditions and composite composition on the physicochemical properties and electric conductivity was studied. The specific surface area, density, morphology, phase composition, thermal properties and electric conductivity of the obtained composites were investigated. The results of studies of composites obtained in an autoclave and in a microwave reactor were compared.
In this work, the authors proposed a modification of the working space one-strand tundish adapted for slab casting process. Numerical simulations of liquid steel flow in the considered flow reactor were performed. The tundish is equipped with a dam with a multi-hole filter. Two variants of the filter hole arrangement were tested and their effect on the liquid steel flow hydrodynamic structure in the tundish was examined. The computer calculations results were verified by performing experiments on the water model. The result of numerical and physical simulations an RTD (Residence Time Distribution) type F curve was generated, which define the transition zone between the cast steel grades during the sequential casting process. The results of the researches showed that the modification of a dam with a multi-hole filter affects on the formation of the liquid steel flow hydrodynamic structure and the transition zone. Furthermore, examinations of the liquid steel refining ability in the considered tundish were carried out. The influence of the filter holes arrangement on the non-metallic inclusions flotation process to the slag phase and liquid steel filtration processes was checked. Numerical simulations were performed in the Ansys-Fluent computer program.
The article presents the results of research concerning AlCu4MgSi alloy ingots produced using horizontal continuous casting process under variable conditions of casting speed and cooling liquid flow through the crystallizer. The mechanical properties and structure of the obtained ingots were correlated with the process parameters. On the basis of the obtained results, it has been shown that depending on the cooling rate and the intensity of convection during solidification, significant differences in the mechanical properties and structure and of the ingots can occur. The research has shown that, as the casting speed and the flow rate of the cooling liquid increase, the hardness of the test samples decreases, while their elongation increases, which is related to the increase of the average grain size. Also, the morphology of the intermetallic phases precipitations lattice, as well as the centerline porosity and dendrite expansion, significantly affect the tensile strength and fracture mechanism of the tested ingots.
The article reports the results of a comparative analysis made for three novel unconventional gear wheel forging processes based on the authors’ patented [5,6,21] plastic forming methods developed chiefly for the purposes of extruding hollow products as well as valves and pins. These processes are distinguished by the fact that part of the tooling elements which are normally fixed during conventional forging are purposefully set in motion. This is intended to change the conditions of friction at the metal-tool contact surface and to induce additional thermal effects due to the transformation of the plastic deformation energy into thermal energy and, as a consequence, to improve the plastic flow of metal and to reduce the force parameters of the process.
The influence of the electrode geometry on the microstructure and corrosion behaviour of Co-Mo nano-crystalline coatings elaborated by electrodeposition is studied. The corrosion behaviour was determined in the Ringer’s solution at 25°C. Electrodeposition mechanisms are also discussed as a function of the electrode geometry. The electrode geometry was found to affect the growth rate and, under certain conditions, the microstructure (existence of channels and pores). It does not have influence on the corrosion behaviour.
In this work, three ceramic composite coatings Al2O3-3TiO2 C, Al2O3-13TiO2 C, and Al2O3-13TiO2 N were plasma sprayed on steel substrates. They were deposited with two conventional powders differing the volume fraction of TiO2 and nanostructured powder. The mechanical and tribological properties of the coatings were investigated and compared. The increase in TiO2 content from 3 wt.% to 13 wt.% in the conventional feedstock improved the mechanical properties and abrasion resistance of coatings. However, the size of the used powder grains had a much stronger influence on the properties of deposited coatings than the content of the titania phase. The Al2O3-13TiO2 coating obtained from nanostructured powder revealed significantly better properties than that plasma sprayed using conventional powder, i.e. 22% higher microhardness, 19% lower friction coefficient, and over twice as good abrasive wear resistance. In turn, the Al2O3-13TiO2 conventional coating showed an increase in microhardness and abrasive wear resistance, 36% and 43%, respectively, and 6% higher coefficient of friction compared to the Al2O3-3TiO2 conventional coating.
Modified Bohm’s formalism was applied to solve the problem of abstruse layer depth profiles measured by the Auger electron spectroscopy technique in real physical systems. The desorbed carbon/passive layer on an NiTi substrate and the adsorbed oxygen/ surface of an NiTi alloy were studied. It was shown that the abstruse layer profiles can be converted to real layer structures using the modified Bohm’s theory, where the quantum potential is due to the Auger electron effect. It is also pointed out that the stationary probability density predicts the multilayer structures of the abstruse depth profiles that are caused by the carbon desorption and oxygen adsorption processes. The criterion for a kind of break or “cut” between the physical and unphysical multilayer systems was found. We conclude with the statement that the physics can also be characterised by the abstruse measurement and modified Bohm’s formalism.
The influence on the corrosion behaviour of Co-Mo nano-crystalline coatings of dissolved oxygen is studied in the Ringer’s solution and artificial saliva at 25°C. This was done by means of potentiodynamic tests and surface observations. It was shown that dissolved oxygen has no influence on passivity, oxidation of the coating and selective dissolution of cobalt. By contrast, dissolved oxygen affects corrosion. General corrosion was observed in the Ringer’s solution whereas pitting corrosion was found in artificial saliva.
Hot Isostatic Pressing elaboration of Norem02, an austenitic-ferritic hypereutectoid stainless steel, leads to the formation of an austenitic matrix with a mixture of acicular M7C3 and globular M23C6 carbides. The sintering tests, carried out by using an AISI 304L container, showed that the final microstructure and the carbides’ distribution of the HIPed Norem02 are strongly influenced by the process parameters (heating and cooling rate, sintering time, holding temperature and pressure) and by the particles’ size, microstructure and phase distribution of the initial powder. The morphological, crystallographic and chemical analysis of the sintered samples were completed by comprehension of the diffusion phenomena at the Norem02/304L interface, enabling the establishment of a correlation between elaboration process and final microstructure.
This paper analyses the heat treatment of the hot-dip zinc coating deposited on both cast iron and steel. The aim of research is to increase coating hardness and wear resistance without decreasing its anticorrosion properties. Hot-dip zinc coating was deposited in industrial conditions (acc. PN-EN ISO 10684) on disc shape samples and bolts M12x60. The achieved results were assessed on the basis of microscopic observation (with the use of an optical and scanning microscope), EDS (point and linear) analysis and micro-hardness measurements. It was discovered that the heat treatment of zinc coating results in an increase in hardness which is caused by the corresponding changes in microstructure.
A method of using the electric charge in a capacitor was applied for the manufacture of thermocouple micro-joints. The motivation for the study was the need to produce a stable welded connection without affecting the geometry of the substrate, which was a thin sheet of Inconel 625 alloy (UNS designation N06625). Within the framework of the research work, a suitable workstation for micro-joints elaboration was built and welding experiments were performed using different electric charges. Studies carried out within the framework of the present work have shown that joints based on Inconel 625 alloy and platinum have the best application properties in the range of small-scale temperature measurements. They can be used, e.g., for monitoring the temperature distribution on the inner surfaces of electric motor casings. An undeniable advantage is in this case the high thermal resistance of both materials used to produce the joint, i.e. the Inconel 625 alloy and platinum. This allows them to be used at high temperatures under atmospheric conditions.
The five-layer Aurivillius type structures with the general chemical formula Bi5Fe2-xMnxTi3O18, where x = 0, 0.6, 1.2 have been synthesized and tested. The SEM studies showed a significant increase in grain size in the manganese-modified Aurivillius type ceramic material (for x = 1.2). The increase in the amount of manganese ions (Mn3+) affects the decrease in the temperature at which the relaxation processes take place. Namely from 525 K (1 kHz) and 725 K (1 MHz) for BFT sample (x = 0) to 355 K (1 kHz) and 565 K (1 MHz) for BFM12T sample (x = 1.2). Using the Arrhenius’s law and the Vogel-Fulcher’s relationship the activation energy (Ea) and the relaxation time have been calculated. The value of Ea increases with the increase of the Mn amount from 0.737 eV (for x = 0) to 0.915 eV (for x = 1.2).
Many wire products (e.g. nets) are made from galvanized material. The hot dip galvanizing process gives the possibility of applying in a respectively thick coat of zinc (also depending on the time of staying wires in the bath) which provides the protection of the product against corrosion. In the available literature there were no research concerned with the influence of hot dip galvanizing process on the mechanical properties TRIP structure steel wires. Therefore, an experiment was carried out in laboratory conditions allowing the determination of the influence of hot dip galvanizing process parameters on the mechanical properties (tensile strength UST and yield strength YS) of TRIP steel wires as well as on the amount of retained austenite in their structure. It has been stated that the hot galvanizing process of TRIP steel wires influences, proportionally to the time of staying wires in zinc bath, on their plastic properties (the increase in yield strength YS) as well as the decrease in the amount of retained austenite in their structure. Such a phenomenon can be caused by stresses responsible for rapid heating of the wire put in the zinc bath in temperature of 450°C and by the strengthening of the materials resulting from the transformation of retained austenite.
This paper presents results obtained from a laboratory investigation conducted on material from a pressure vessel after longterm operation in the oil refinery industry. The tested material contained structural defects which arose from improper heat treatment during steel plate manufacturing. Complex tensile tests with acoustic emission signal recording were conducted on both notched and unnotched specimens. The detailed analysis of different acoustic emission criteria allowed as to detect each stage of plastic deformation and microstructural damage processes after a long-term operation, and unused carbon steels during quasi-static axial tension testing. The acoustic emission activity, generated in the typical stages of material deformation, was correlated by microscopy observations during the tensile test. The results are to be used as the basis for new algorithms for the assessment of the structural condition of in-service pressure equipment.
The paper presents the results of studies of hybrid composite layers Ni/Al2O3/Cgraphite produced by the electrodeposition method. Three variants of hybrid composite layers were prepared in electrolyte solutions with the same amounts of each dispersion phases which were equal to 0.25; 0.50 and 0.75 g/dm3. The structure of Ni/Al2O3/Cgraphite layers as well as the Al2O3 and graphite powders, which were used as dispersion phases was investigated. The results of morphology and surface topography of produced layers are presented. The modulus of elasticity and microhardness of the material of produced layers were determined by DSI method. Tribological and corrosion resistance tests of produced layers were carried out. Realized studies have shown that the material of the produced layers is characterized by a nanocrystalline structure. Incorporation of dispersion phases into the nickiel matrix increases the degree of surface development of layers. Ni/Al2O3/Cgraphite layers are characterized by high hardness and abrasion resistance by friction, furthermore, they provide good corrosion protection for the substrate material.
In this paper, the deviation from eutectic composition in boundary layer for eutectic growth is studied by phase-field method. According to a series of artificial phase diagram, the lamellar eutectic growth of these alloy is simulated during directional solidification. At steady state, average growth velocity of eutectic lamella is equal to the pulling velocity. With the increasing of the liquidus slope of β phase, the average composition in boundary layer would deviate from eutectic composition and the deviation increases. The constitutional undercooling difference between both solid phases caused by the deviation increases with the increasing of the deviation. The β phase would develop a depression under the influence of the deviation.
The article presents a novel method that allows measurement of thermal conductivity that is based on Stefan-Boltzmann law. The developed method can be used to determine thermal conductivity of ceramic investment casting molds. The methodology for conducting thermal conductivity tests of ceramic material samples is presented. Knowledge of the value of thermal capacity and thermal conductivity as a function of temperature enables computer simulations of the process of cooling and solidification of liquid metal in a mold.
The paper discusses the results of investigations of material, tribological and anti-corrosion properties of hybrid coatings of the Cr/CrN type, consisting of chromium and chromium nitride, formed on the surface of alloy tool steel by the Arc-PVD method. Investigations of the morphology and microstructure of hybrid coatings, as well as of their phase composition were carried out. The studies on mechanical properties included tests on hardness and Young’s modulus using the nanoindentation method. Tests on adhesion were conducted using the scratch-test method. Tribological properties of the obtained coatings were evaluated by the pin-on-disc method. Resistance to corrosion was determined by electrochemical methods. It was shown that hybrid coatings of the Cr/CrN type are characterized by good adhesion to the substrate and very good tribological properties, as well as by very good resistance to corrosion in a solution containing chlorine ions.
Sound joint of hollow-extruded 6005A-T6 aluminum alloy was achieved by friction stir welding and its high cycle fatigue performance was mainly investigated. As a result, the joint fatigue limit reaches 128.1 MPa which is 55% of the joint tensile strength. The fatigue fracture mainly occurs at the boundary between the stir zone and thermo-mechanically affected zone due to the large difference in the grain size. This difference is caused by the layered microstructure of the base material. The shell pattern with parallel arcs is the typical morphology in the fracture surface and the distance between arcs is increased with the increase of stress level. The specimen with the fracture located in the stir zone possesses a relatively low fatigue life.
The present work discusses results of increased temperature on shape-dimensional changes of a 110 type hose coupling, produced from EN AC-AlSi11 alloy with the use of pressure die casting technology. The castings were soaked for 3.5 h at temperatures 460°C, 475°C and 490°C. The verification of shape-dimensional accuracy of the elements after soaking treatment, in relation to raw casting, was carried out by comparing the 3D models received from 3D scanning. Soaking temperature of about 460°C-475°C results in no significant changes in the shapes and dimensions of the castings, or surface defects in the form of blisters, which can be seen at a temperature of 490°C.
The paper presents the results of research on the influence of sintering temperature on microstructure, DC electrical conductivity, dielectric, ferroelectric and magnetic properties of PbFe1/2Nb1/2O3 ceramics doped by Li in the amount of 5.0% wt., in the abbreviation PLiFN. The ceramic samples of the PLiFN material were obtained by the two-stage synthesis – columbite method and sintered by free sintering methods. Introduction to the basic PbFe1/2Nb1/2O3 composition of the lithium admixture to decrease the electrical conductivity and reduction of dielectric loss. The tests have shown that the increase in sintering temperature orders the PLiFN ceramic microstructure, which has a positive effect on its electrophysical properties. At room temperature, the PLiFN ceramic samples show both ferroelectric and ferromagnetic properties. Considering the functional parameters of the obtained ceramic samples, the optimal technological conditions are 1100°C/2 h.
The objective of the research in this work was the modification of structure of carbide-type chromized layers, by the combination of diffusion chromizing with subsequent PVD treatment, consisting of chromium nitride deposition, carried out to improve their tribological properties. As a result, hybrid layers on the surface of tool steel were obtained. For comparison, the properties of single chromized carbide layers obtained in a diffusion chromizing process were tested. Investigations of layer microstructure, their mechanical properties, surface topography, adhesion of layers to the steel substrate, as well as tribological properties were conducted. The layer microstructure was characterized by X-ray diffraction and scanning electron microscopy. Topography of the layer surface was studied by an optical profilometer. The scratch test for investigations of layers adhesion to the steel substrate was used. Testing of tribological properties (linear wear) of the layers was performed by the three-cylinder-cone method. It was shown, that hybrid layers are characterized by a significantly smaller surface roughness than that of chromized carbide layers and their wear resistance improved almost twice with respect to carbide layers.
The numerical algorithm of thermal phenomena is based on the solution of the heat conduction equations in Petrov-Galerkin’s formula using the finite element method. In the modeling of phase transformation in the solid state, the models based on the diagrams of continuous heating and continuous cooling (CHT and CCT). In the modeling of mechanical phenomena, equations of equilibrium and constitutive relationships were adopted in the rate form. It was assumed that the hardened material is elastic-plastic, and the plasticizing can be characterized by isotropic, kinematic or mixed strengthening. In the model of mechanical phenomena besides thermal, plastic and structural strains, the transformations plasticity was taken into account. Thermo-physical size occurring in the constitutive relationship, such as Young’s modulus and tangential modulus, while yield point depend on temperature and phase composition of the material. The modified Leblond model was used to determine transformation plasticity. This model was supplemented by an algorithm of modified plane strain state, advantageous in application to the modeling of mechanical phenomena in slender objects. The problem of thermoelasticity and plasticity was solved by the FEM. In order to evaluate the quality and usefulness of the presented numerical models, numerical analysis of temperature fields, phase fractions, stresses and strains was performed, i.e. the basic phenomena accompanying surface layer of progressive-hardening with a movable heat source of slender elements made of tool steel for cold work.
The paper presents investigations of microstructure of varistors of damaged surge arrester counters. A similar ZnO varistor, not subjected before to operation, was a point of reference in this research. The results of investigations of the ZnO varistors show an untypical phase composition of their material, which was characterized by unsatisfying homogeneity and cohesion. The degradation processes of varistor material in the subsequent stages were recognized and described. A harmful impact of humidity inside the untight surge arrester counter on its operation and its ZnO varistors was proved. Some conclusions being the result of the operation checking of surge arrester counters were presented too.