Search results

Filters

  • Journals

Search results

Number of results: 74
items per page: 25 50 75
Sort by:

Abstract

In this study, atlases of wave characteristics and wave energy for the Barents Sea have been generated for the years from 1996 to 2015 based on ERA-Interim datasets from the European Centre for Medium-Range Weather Forecasts (ECMWF). The wave power resources in the Barents Sea can be exploited with sea ice extent declining in recent years. The entire Barents Sea has been divided into multi-year sea ice zones, seasonal sea ice zones and open water zones according to the 20-year averaged sea ice concentration. In the entire domain, the spatial distributions of the annual averaged and mean monthly significant wave heights and wave energy flux are presented. For the open water zones, 15 points have been selected at different locations so as to derive and study the wave energy roses and the inter-annual wave power variation. Moreover, the correlations between the wave energy period and the significant wave height are shown in the energy and scatter diagrams. The maximum wave power occurs in the winter in the western parts of the Barents Sea with more than 60kW/m. The wave energy can therefore be exploited in the open water zones.
Go to article

Abstract

This paper reports on a morphometric analysis of land-terminating glaciers on southern and western Spitsbergen in the years 1936–2014. An attempt was made to estimate the deglaciation rate and the scale of its acceleration in the 21st century in the conditions of Arctic amplification. Satellite scenes and topographic map sheets were used for the study and were analyzed by means of remote sensing and GIS methods. The study covered 2000–2014 years and concluded that surface recession accelerated on average by a factor of 2.75 compared to the 1936–2000 period, while linear recession was 2.2 times faster. The greatest increase in the deglaciation rate can be observed in the case of glaciers faced to N and W sectors. The deglaciation process is the most advanced in the central part of the island, where small, compact mountain glaciers predominate. In recent years, a slowdown in the deglaciation processes in these glaciers was observed. The studies demonstrate that the deglaciation rate was mainly influenced by the basin relief determining the glacier geometry. The resultant fractal nature of the ice cover makes it highly vulnerable to the disintegration of complex glacial systems into smaller ones due to glacier thinning and the separation of outlets. The acceleration of the deglaciation rate in turn is modified by the climate factor, especially the impact of warming air masses from the N and W sectors where seas are becoming increasingly ice-free and, consequently, have an increasing heat capacity.
Go to article

Abstract

A total number of 156 palaeomagnetic specimens of metacarbonates from 9 sites in Blomstrandhalvøya and Lovénøyane (Kongsfjorden, western Spitsbergen) and an additional 77 specimens of unmetamorphosed sediments infilling fractures (4 sites) within the Caledonian metamorphic basement of Blomstrandhalvøya were demagnetized. No relicts of pre-metamorphic magnetization were identified. The Natural Remanent Magnetization (NRM) pattern of metacarbonates is dominated by Caledonian (sensu lato) – Svalbardian and Late Mesozoic/Cenozoic secondary magnetic overprints carried by the pyrrhotite and magnetite/maghemite phases, respectively. The NRM of unmetamorphosed sediments infilling the karstic/tectonic fractures is dominated by hematite carrier. It revealed three stages of magnetization: Caledonian sensu lato, Carboniferous and Late Mesozoic/Cenozoic, which can be related to their initial fracturing, karstification and sedimentation or reactivation. As the majority of the palaeopoles calculated for the Kongsfjorden sites fit the 430 – 0 Ma sector of Laurussia reference path in an in situ orientation these results support the hypothesis that Blomstrandhalvøya and Lovénøyane escaped main Eurekan deformations. The potential rotation of the Kongsfjorden basement by any west dipping listric fault activity rotating the succession accompanying the opening of North Atlantic Ocean was not documented by the palaeomagnetic data presented here.
Go to article

Abstract

Geomorphological research based on geomorphological mapping seeks to identify the origins and age of forms as well as to describe the process that created or transformed a particular form. One of the most important aspects of this study is the morphometry and morphology of the landscape. This also applies to the submarine areas, and issues related to marine geomorphometry. Bathymetric data used in this study were obtained from the measurements of the Norwegian Hydrographic Service and measurements conducted by the authors. Its main goal was: to determine the bathymetry of the Recherchefjorden (Bellsund, Svalbard), establish morphometric parameters for the analysis of the morphology of the bottom. The boundaries of zones, related to the specific character of bottom geomorphology linked with geological structure, tectonics and, in particular, the impact of glacial system, was delineated. The sets of landforms (areas) were distinguished based on the morphometric analysis resulting from the determined parameters: slopes, its aspects, curvatures and Bathymetric Position Index. Basically, this areas are concentrated in two zones: the main Recherchefjorden and its surroundings. The delimitation also takes into account the origins and location of theme in relation to the glacial systems. On this basis, moraine areas were distinguished. They are linked with the Holocene advances of two glaciers, Renardbeen and Recherchebreen, mainly during the Little Ice Age. They constitute boundary zones between areas with different morphometric parameters: outer fjord and inner fjord. Moreover, taking into account geology and terrestrial geomorphology it was possible to describe paraglacial processes in this area.
Go to article

Abstract

Rock glaciers are lobate or tongue-shaped landforms which consist of rock debris and have either an ice core or an ice-cemented matrix. Characteristics such as the landscape setting, morphology, material and current geomorphological state are universally used to classify rock glaciers. In Antarctica, rock glaciers have only been surveyed on the Antarctic Peninsula, Ellsworth Mountains and in Victoria Land. This paper presents the first data on the identification and description of rock glaciers in the Jutulsessen nunataks, Dronning Maud Land, East Antarctica. The rock glaciers in the Jutulsessen exhibit a variety of morphologies and states. Our data suggests that the rock glaciers in Brugdedalen and Jutuldalen are active, while the features at Vassdalen and Grjotlia are considered inactive, and a feature at Grjotøyra is considered relict. The described rock glaciers do not fit into existing classification systems and appear to be different to alpine, Arctic and Andean rock glaciers. They further present examples that fit both the ‘glaciogenic’ and ‘permafrost’ development theories.
Go to article

Abstract

Gas emission from casting moulds, cores and coatings applied for sand and permanent moulds is one of the fundamental reasons of casting defects occurrence. In the previous studies, gas emission was measured in two ways: normalized, in which the evolving gas volume was measured during heating of the moulding sand sample in a sealed flask, or by measuring the amount of gas from sand core (sample) which is produced during the pouring of liquid metal. After the pouring process the sand mould is heated very unequally, the most heated areas are layers adjacent to the liquid metal. The emission of gas is significantly larger from the surface layer than from the remaining ones. New, original method of measuring kinetics of gas emission from very thin layers of sand moulds heated by liquid metal developed by the authors is presented in the hereby paper. Description of this new method and the investigation results of kinetics of gas emission from moulding sand with furan and alkyd resin are shown. Liquid grey cast iron and Al-Si alloy were used as a heat source in the sand moulds. Comparison of the kinetics of gas emission of these two kinds of moulding sands filled with two different alloys was made. The momentary metal temperature in sand mould was assigned to the kinetics of gas emission, what creates a full view of the possibility of formation of casting defects of the gaseous origin. Moulding sand with alkyd resin is characterized by larger gas emission; however gases are emitted slower than in the case of moulding sands with furan resin. This new investigation method has a high repeatability and is the only one which gives a full view of phenomenon’s in the surface layer which determines quality of the casings. The obtained results are presented on several graphs and analyzed in detail. They have a great application value and can be used in the production of iron as well as light metal alloy castings.
Go to article

Abstract

The paper presents an innovative method of creating the layered castings. The innovation relies on application the 3D printing insert obtaining in SLM (selective laser melting) method. This type of scaffold insert made from pure Ti powder, was placed into mould cavity directly before pouring by grey cast iron. In result of used method was obtained grey cast iron casting with surface layer reinforced by titanium carbides. In range of studies were carried out metallographic researches using light microscope and scanning electron microscope, microhardness measurements and abrasive wear resistance. On the basis of obtaining results was stated that there is a possibility of reinforcing surface layer of the grey cast iron casting by using 3D printing scaffold insert in the method of mould cavity preparation. Moreover there was a local increase in hardness and abrasive wear resistance in spite of the precipitation of titanium carbides in surface layer of grey cast iron. While the usable properties of composite surface layer obtained in result of use of the method presented in the paper, strongly depend of dimensions of scaffold insert, mainly parameters Re and Ri.
Go to article

Abstract

The present paper is a presentation of results of a study on morphology, chemical composition, material properties (HVIT, HIT, EIT), and nanoindentation elastic and plastic work for carbide precipitates in chromium cast iron containing 24% Cr. It has been found that the carbides differ in chemical composition, as well as in morphology and values characterizing their material properties. The carbides containing the most chromium which had the shape of thick and long needles were characterized with highest values of the analyzed material properties.
Go to article

Abstract

This article discusses results of an analysis of mechanical properties of a sintered material obtained from a mixture of elemental iron, copper and nickel powders ball milled for 60 hours. The powder consolidation was performed by hot pressing in a graphite mould. The hot pressing was carried out for 3 minutes at 900 °C and under a pressure of 35 MPa. The sintered specimens were tested for density, porosity, hardness and tensile strength. Their microstructures and fracture surfaces were also examined using a scanning electron microscope (SEM). The study was conducted in order to determine the suitability of the sintered material for the manufacture of metal-bonded diamond tools. It was important to assess the effects of chemical composition and microstructure of the sintered material on its mechanical properties, which were compared with those of conventional metal bond material produced from a hot-pressed SMS grade cobalt powder. Although the studied material shows slightly lower strength and ductility as compared with cobalt, its hardness and offset yield strength are sufficiently high to meet the criteria for less demanding applications.
Go to article

Abstract

In the knock-out process, as well as in the preliminary phase of moulding sand reclamation, the issue of energy demand for the process of crushing used sand agglutinations, preferably to single grains, is particularly important. At present, numerical values of moulding sand impact resistance, which would allow energy-related aspects of this process to be forecast, are not known, as such research has not been carried out. It seems that impact resistance tested on very small cross-section samples, which allows us to very precisely reveal some unique features of a moulding sand with organic and inorganic binders, is an important parameter, which so far has not been taken into account for evaluation of mechanical properties of moulding sands. Preliminary attempts to determine impact resistance of moulding sands have been carried out as part of own research of the author. The conducted investigations aimed at determining the relationships between the obtained values of tensile strength and impact resistance of moulding sands. In addition, the effect of holding samples at temperatures of 100oC, 200oC, 300oC on the value of impact resistance was determined, both for sands made with fresh and with reclaimed sand grains.
Go to article

Abstract

This article discusses issues related to continuous casting of brass. The tested material was CuZn39Pb2 brass with the use of continuous casting and different parameters of the process. The position consists of a melting furnace with a graphite refining pot of about 4000 cm3 chuting capacity, a graphite crystallizer of 9,5 mm nominal diameter, a primary and secondary cooling system and an extracting system as well. The analysis was carried out in terms of technological parameters of the process and type of charge. Highlighted: feedrate ingot, number of stops, and technological temperatures. The surface quality of the obtained ingots and the structure were analyzed. The most favorable conditions were indicated and technological recommendations indicated. They have been distinguished for ingots for plasticity and other technologies. Favorable casting conditions are low feed and low temperature. Due to the presence of impurities coming from the charge it is disadvantageous to have Ni greater than 0.053% by mass, and Fe more than 0.075% by mass. It is recommended to maintain a high zinc content in the melt which is associated with non-overheating of the metal during casting and earlier melting.
Go to article

Abstract

Energy conservation is an important step to overcome the energy crisis and prevent environmental pollution. Casting industry is a major consumer of energy among all the industries. The distribution of electrical energy consumed in all the departments of the foundry is presented. Nearly 70% of the energy is consumed especially in the melting department alone. Production of casting involves number of process variables. Even though lot of efforts has been taken to prevent defects, it occurs in the casting due to variables present in the process. This paper focuses the energy saving by improving the casting yield and by reducing the rejections. Furthermore an analysis is made on power consumption for melting in the induction furnace to produce defective castings and improvement in the casting yield. The energy consumed to produce defective castings in all other departments is also presented. This analysis reveals that without any further investment in the foundry, it is possible to save 3248.15 kWh of energy by reducing the rejections as well as by improving the casting yield. The redesign of the feeding system and the reduced major rejection shrinkage in the body casting improved the casting yield from 56% to 72% and also the effective yield from 12.89% to 66.80%.
Go to article

Abstract

The determination of the form of a probability density function (PDF3) of diameters for nodular particles by using a probability density function (PDF2), which form is empirically estimated from cross-sections of these nodules in a metallographic specimen, can be regarded as a special case of Wicksell's corpuscle problem (WCP). The estimation of the PDF3 for the nodular particles provides information about the kinetics of these particles nucleation, and so about the kinetics of their growth. This information is essential for building more accurate mathematical models of the alloy crystallization. In the paper there are presented two derivations of the methods used for the estimation of the PDF3 form. The first method bases on diameters received from a planar cross-section. The second one uses also data from the planar cross-section but not the diameters only chords. Both methods provide practical rules for the analysis of the empirical diameters’ and chord’s size distribution and allow to estimate the mean value of the external surface area of the particles.
Go to article

This page uses 'cookies'. Learn more