The article presents an analysis of stresses in the current tool system of the die during the implementation of the third forging operation of the screw M12 class 10.9 with cylinder head and hexagonal socket. It was assumed that the level of negative cracking due to stress can be reduced by using a mounting interference between the die and the tube blank. Due to the design of the tool system value of the die, the interference value cannot be too large. Therefore, an analysis of the influence of the interference between the die and the tube blank in a die tool system on the value and distribution of stresses in the individual components. An analysis of the assembly stresses and the stresses occurring during the process of deformation of the shaped head of the screw was done. The calculations were performed using a commercial software package MARC / Mentat.
Anisotropic rotor configurations influenced by the presence of a large number of geometrical parameters in a permanent magnet assisted synchronous reluctance (PMASR) motor pose design challenges in obtaining a robust geometry satisfying the requirements of reduced torque ripple and high torque density. Therefore, the purpose of this work is to perform detailed geometrical sensitivity analysis of a 36 slot/4 pole permanent magnet assisted synchronous reluctance (PMASR) motor using h-indexing and level sensitivity analysis in order to specify a guideline for designers to prioritize the design variables for optimization. Systematic multi-level design optimization for multiple objectives is implemented by an NSGA-II algorithm aided by the finite element analysis tool, hardware prototyping and experimental validation. The optimized designs also exhibit better structural and thermal characteristics.
Because the heat release of plutonium material, the composite structure is heated and the stress and strain of the composite structure will increase, which will affect the thermodynamic properties of the structure. The thermodynamic analysis of complex structures, which are composed of concentric structures of plutonium, beryllium, tungsten, explosives, and steel, was carried out. The results showed that when the structure is spherical, the temperature is higher than that of the ellipsoid structure. Stress of the elliptical structure is greater than the spherical structure. This study showed that the more flat the shell is, the greater the stress concentration point occurs at the long axis, and the maximum stress occurs at the beryllium layer. These conclusions provide theoretical support for the plutonium composite component testing.
Residual stress has a great influence on the metal, but it is difficult to measure at small area using a general method. Residual stress calculations using the Vickers indentation can solve this problem. In this paper, a numerical simulation has been made for the residual stress measurement method of metal material deformed by high-speed impact. Then, the stress-strain curve at the high-speed deformation was confirmed through actual experiments, and the residual stresses generated thereafter were calculated by the Vickers indenter method. A Vickers indentation analysis under the same conditions was performed at the position where a residual stress of about 169.39 MPa was generated. Experiments were carried out and high speed impact was applied to the specimen to generate residual stress. The obtained results indicate that it is possible to identify residual stresses in various metals with various shapes through Vickers indentation measurements, and to use them for process and quality control.
Digital photoelasticity is an important optical metrology follow-up for stress and strain analysis using full-field digital photographic images. Advances in digital image processing, data acquisition, procedures for pattern recognition and storage capacity enable the use of the computer-aided technique in automation and facilitate improvement of the digital photoelastic technique. The objective of this research is to find new equations for a novel phase-shifting method in digital photoelasticity. Some innovations are proposed. In terms of phaseshifting, only the analyzer is rotated, and the other equations are deduced by applying a new numerical technique instead of the usual algebraic techniques. This approach can be used to calculate a larger sequence of images. Each image represents a pattern and a measurement of the stresses present in the object. A decrease in the mean errors was obtained by increasing the number of observations. A reduction in the difference between the theoretical and experimental values of stresses was obtained by increasing the number of images in the equations for calculating phase. Every photographic image has errors and random noise, but the uncertainties due to these effects can be reduced with a larger number of observations. The proposed method with many images and high accuracy is a good alternative to the photoelastic techniques.
In the paper, a solution to the problem of elastic deformation of thin-walled shell structures with complex shapes within the theory of geometrically non-linear shells has been presented. It is a modification of the Newton-Raphson method. In a variational formulation, the problem is based on a Lagrange’s functional for increments of displacements. The method has been applied to investigations of a harmonic drive, in particular to analysis of the stress state in the flexspline with a variable curvature as well as bearings of the generator. For verification of the obtained results, a more adequate FEM model calculated by ANSYS has been used.
This paper describes multiple electric field control methods for foil coils in high-voltage coreless linear actuators and their sensitivity to misalignment. The investigated field control methods consist of resistive, refractive, capacitive and geometrical solutions for mitigating electric stress at edges and corners of foil coils. These field control methods are evaluated using 2-D boundary element and finite element methods. A comparison is presented between the field control methods and their ability to mitigate electric stress in coreless linear actuators. Furthermore, the sensitivity to misalignment of the field control methods is investigated.
Three-dimensional (3D) finite element analyses (FEA) are performed to simulate the local compression (LC) technique on the clamped single-edge notched tension (SE(T)) specimens. The analysis includes three types of indenters, which are single pair of cylinder indenters (SPCI), double pairs of cylinder indenters (DPCI) and single pair of ring indenters (SPRI). The distribution of the residual stress in the crack opening direction in the uncracked ligament of the specimen is evaluated. The outcome of this study can facilitate the use of LC technique on SE(T) specimens.
This article employs the classical Euler–Bernoulli beam theory in connection with Green–Naghdi’s generalized thermoelasticity theory without energy dissipation to investigate the vibrating microbeam. The microbeam is considered with linearly varying thickness and subjected to various boundary conditions. The heat and motion equations are obtained using the modified couple stress analysis in terms of deflection with only one material length-scale parameter to capture the size-dependent behavior. Various combinations of free, simply-supported, and clamped boundary conditions are presented. The effect of length-to-thickness ratio, as well as the influence of both couple stress parameter and thermoelastic coupling, are all discussed. Furthermore, the effect of reference temperature on the eigenfrequency is also investigated. The vibration frequencies indicate that the tapered microbeam modeled by modified couple stress analysis causes more responses than that modeled by classical continuum beam theory, even the thermoelastic coupled is taken into account.