This paper presents an evaluation of the Hypoplastic Clay constitutive model for finite element analysis of deep excavations and displacements induced by excavations in the influence zone. A detailed description and formulation of the Hypoplastic Clay soil model is included. A parametric case study of a deep excavation executed in Pliocene clays is presented. FE analysis was performed using several soil models (Mohr-Coulomb, Modified Mohr-Coulomb, Drucker-Prager, Modified Cam-Clay, Hypoplastic Clay) and the results were compared to in-situ displacements measurements taken during construction. Final conclusions concerning the suitability of the Hypoplastic Clay model for deep excavation modelling in terms of accurate determination of horizontal displacements of the excavation wall, the uplift of the bottom of excavation, and, most importantly,vertical displacements of the terrain in the vicinity of the excavation are presented.
Risks pertaining to construction work relate to situations in which various events may randomly change the duration and cost of the project or worsen its quality. Because of possible significant changes of random events, favorable, moderate, and difficult conditions of construction work are considered. It is the first stage of the construction risk analysis. The probabilistic parameters of construction are identified and described by using the design characteristics model of the structure and the construction technology model. The first describes the probabilistic properties of the structure execution's technology. The second describes the probabilistic properties of the works execution. Both models contain basic probabilistic data for scheduling, cost estimating, and risk assessment of the construction.
The paper present the concept of stability assessing the of solutions which are construction schedules. Rank have been obtained through the use of task scheduling rules and the application of the KASS software. The aim of the work is the choice of the equivalent solution in terms of the total time of the project. The selected solution optimization task should be characterized by the highest resistance to harmful environmental risk factors. To asses the stability of schedule simulation technique was used.
In 2015 an important part of the official evaluation of Polish scientific journals was left to experts’ judgement. In this paper we try to establish which observable factors (with available data) are closely related to the outcome of experts’ evaluation of Polish journals in economic sciences. Using the multiple regression statistical model we show that only 5 variables (out of 17) significantly explain almost 50% of the empirical variance of the experts’ evaluation. The determinants of particular interest, not entering the formal criteria and not related to the impact on global science, are: the number of citations mainly in Polish journals and the affiliation with the Polish Academy of Sciences.
The article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental modelling of an installation containing a heat accumulator is presented.
The paper focuses on the modelling of bromate formation. An axial dispersion model was proposed to integrate the non-ideal mixing, mass-transfer and a kinetic model that links ozone decomposition reactions fromthe Tomiyasu, Fukutomi and Gordon (TFG) ozone decaymodelwith direct and indirect bromide oxidation reactions, oxidation of natural organicmatter and its reactionswith aqueous bromine. To elucidate the role of ammonia an additional set of reactions leading to bromamine formation, oxidation and disproportionation was incorporated in the kinetic model. Sensitivity analysis was conducted to obtain information on reliability of the reaction rate constants used and to simplify the model.
“Mineral deposit model”, “deposit modelling” are the terms commonly used, although imprecise. This is often identified as the application of computerized methods to the elaboration and presentation of geological information, in particular for the mining design. Deposit modelling is the mode of presentation of deposit features, which in the meaning of the authors of such presentation, describes the deposit features between the points of observations as best as possible. Deposit modelling has a long history (XVI-XVII centuries), however such a term was not used. Varied methods of cartographic presentation of deposits and their features were proposed. The progress in the presentation of the deposit in space using isolines maps has led to the separation of methods of deposits geometrisation. Over time, a simple mathematical statistics method was used to describe the deposit parameters, followed by geostatistical methods. Some of them were however not commonly used as too troublesome. The computer based approach to the presentation of geological data has an unquestionable value but is accompanied by the possibility of inappropriate formalized and erroneous interpretations and a presentation as to whether the basic rules of geological knowledge were neglected. Deposits modeling is a conceptual task and cannot be fully automated.
Exploitation of hard coal seams by roadway system is applied by two coal mines in southern Poland in Upper Silesian Basin. It is a secondary mining exploitation carries out in safety pillars of urban areas and shafts within mining areas of closed coal mines. Roadway system is the excavation process of gateways which are made in parallel order leaving coal pillars between them. An optimal width of coal pillar makes roadway stable and reduces subsidence of terrain surface. The article presents results of subsidence simulation caused by partial extraction using empirical and numerical methods on the example of one exploitation field of “Siltech” coal mine. The asymptotic state of subsidence was considered after mining ceased in the study area. In order to simulate of subsidence, numerical model of rock mass and model of Knothe-Budryk theory were calibrated. Simulation of vertical displacements in numerical method was carried out using RS3 program by Rocscience based on finite element method. The assumption was made that model of rock mass is transversely isotropic medium, in which panels were designed according to order of extraction of coal seams. The results of empirical and numerical methods were compared with measured values of subsidence at benchmarks along drawn lines (subsidence profiles).
The paper is devoted to discussing consequences of the so-called Frisch-Waugh Theorem to posterior inference and Bayesian model comparison. We adopt a generalised normal linear regression framework and weakenits assumptions in order to cover non-normal, jointly elliptical samplingdistributions, autoregressive specifications, additional nuisance parameters andmulti-equation SURE or VAR models. The main result is that inference basedon the original full Bayesian model can be obtained using transformed dataand reduced parameter spaces, provided the prior density for scale or precisionparameters is appropriately modified.
Four Geodynamical Expeditions of the Polish Academy of Sciences carried through wide research seismic program in West Antarctica in 1979-1991. Three of these expeditions operated in the Bransfield Strait. The experiment of deep refraction and wide-angle reflection in West Antarctica focused on deep structure of the lithosphere, mainly of the Earth's crust. The network of deep seismic soundings (DSS) profiles covered all the Bransfield Strait. Five land stations on the South Shetland Islands, three stations on the Antarctic Peninsula and nine ocean bottom seismographs (OBS) recorded seismic waves, generated by explosions in a sea. The Bransfield Rift and the Bransfield Platform form a marginal basin against a volcanic arc of the South Shetland Islands. The paper presents new results of 2-D seismic modeling for network of five selected profiles. Four of them, ranging in lenght from 150 to 190 km, crossed main structures of the Bransfield Strait and the fifth, which connected the other ones and was 310 km long, ran along the Bransfield Rift. Two or three seismic models were presented for each profile. Finally, mutually corrected and controlled 2-D models of described profiles were constructed. They all presented spatial complex structure of the Earth's crust in a young rift of the Bransfield Strait, including extent of its main element i.e. anomalous high velocity body (HVB) (Vp > 7.4 km/s), detected in 10-30 km depth range except profile DSS-4 (southwest part of the Bransfield Strait). This inhomogeneity is interpreted as intrusion of the upper mantle (?asthenosphere) during stretching of the continental crust. The Moho discontinuity was found at depth 30-35 km, with velocities equal to about 8.1 km/s.
The contemporary underground mining of raw minerals is more and more associated with geological and mining software packages which support the work of designers from the moment of the exploration of a deposit, determination of its size and quality, geological, hydrogeological and tectonic conditions, by planning the development and cutting of the deposit. Production planning is one of the most important activities carried out in the course of a mining project, because it allows to set specific production results of a mine in relation to a time unit, and then allows for a verification of the degree of completion of the assumed plan. At present, computer-aided design is applicable to daily or long-term output planning taking deposit, qualitative, quantitative and cost constraints into account. In the article, selected forms of ore deposits were presented. On the basis of several dozen boreholes up to 300m in length, an exemplary fragment of the ore cutting model using computer-aided design of mining works was presented. By using modern computer software - ABB MineScape with modular construction, the possibilities of improving the process of development of future exploitation areas have been determined. In particular, the arrangement of boreholes, based on which ones the cross sections were made with, present the exemplary lithostratigraphic thickness of layers, including the location of discontinuous deformations in the form of faults, and an ore bearing zone. For the block model, resources with priority for metal N o. 1 and 2 were calculated. I n the last section of the article, the cutting idea for a shallow ore deposit has been presented. The degree of effective use of the deposit has been analysed for the room and pillar mining method.
The analysis of changes in the mechanical properties of wooden mining cribs under the influence of different types of exploitation loads is the question for which deals with many domestic and abroad research centers deal with. High The high interest in this subject results from the increase of the conducted depth exploitation, which contributes to the increase in both the vertical pres-sure and the complexity of geological – mining conditions and in- the intensification of natural hazards. Another reason is the tendency of decreasing the thickness of the exploited ores deposits. Wooden crib support is used Both both in underground ore, hard coal and salt mining is used wooden crib support. Mining cribs with various configurations are especially useful for the reinforcement of excavations workings behind the front and for further strengthen of the crossings. In particular, additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock is applied in the ore mining in places where found extended rooms or drifts are found or in places with degraded roof conditions, applies additional reinforcement support in the form of wooden cribs (pile supporting), which shall be left empty or filled with waste rock. During underground ex-ploitation is produced waste Waste rock, which comes from the access, prepar-atory excavations and from ongoing field of exploitation is produced during underground exploitation. In the case of the underground exploitation of cop-per ore, waste rock is used to fill voids after exploitation as rock stowing. It is also used for filling mining wooden cribs, as an artificial support and for harder transportation roads. This paper presents the results of the laboratory strength tests performed on models of four-point timber cribs, built with beams set horizontally, at the ge-ometrical scale of 1:10. In the laboratory research Research wooden cribs models with size 200 × 200 × 200 mm and 100 × 100 × 100 mm were used in the laboratory. The paper describes the maximum loading capacity of the cribs consisted consisting only of beams and filled with waste rocks. In addition, a vertical and appropriate strain of cribs at maximum force was shown. On the basis of laboratory research it was found that the use of the same number of timbers and the management of waste rocks, the filling of the four-point cribs with the waste rocks allowed several times to increase its support to be increased several times.
Validation results of a theoretical model that describes the formation of bromate during ozonation of bromide-containing natural waters are presented. An axial dispersion model integrating the nonideal mixing, mass-transfer and a kinetic model that links ozone decomposition reactions from the Tomiyasu, Fukutomi and Gordon ozone decay model with direct and indirect bromide oxidation reactions, oxidation of natural organicmatter and reactions of dissolved organics and aqueous bromine was verified. Themodel was successfully validated with results obtained both at a laboratory and a full scale. Its applicability to different water supply systems was approved.
The paper presents modeling and simulation results of the operation of a three-phase fluidized bed bioreactorwith partial recirculation of biomass. The proposed quantitative description of the bioreactor takes into account biomass growth on inert carriers, microorganisms decay and interphase biomass transfer. Stationary characteristics of the bioreactor and local stability of steady-stateswere determined. The influence of microbiological growth kinetics on the multiplicity of steady-states was discussed. The relationship between biofilm growth and boundaries of fluidized bed existence was shown.
The author analyses onymic practices of Poznań–based craftsmen forming guilds. In the names of the inhabitants of Poznań, which stabilised until the end of the 18th century, she seeks traces of the so-called cognomens, i.e. secondary personal designations granted to apprentices who were becoming masters. The names resulted from community acts of creation, which were of ludic nature. Referring to German onymic practices and pointing to the so-called Schleifnamen, the author discusses specific codes of European middle-class culture. She focuses on the transfer of models and patterns to Polish urban communities.
Given a linear discrete system with initial state x0 and output function yi , we investigate a low dimensional linear systemthat produces, with a tolerance index ǫ, the same output function when the initial state belongs to a specified set, called ǫ-admissible set, that we characterize by a finite number of inequalities. We also give an algorithm which allows us to determine an ǫ-admissible set.
The complexity of the phenomena associated with the course of the cognitive processes that determine an efficient learning, excludes the possibility of collecting knowledge in other ways than neuronal-information. It excludes also possibilities of interpreting it, in other ways than with use of respectively formalized cognitive models. The presented paper is a kind of summary of the latest achievements in this field.
The article presents a synthetic analysis of the crude oil market in Poland. As of today, this safety is provided mainly on the basis of native lignite and hard coal resources. However, the analysis of the hard coal market conducted by the authors indicates that the carried out mining restructuring (among others) led to an excessive reduction of mining volume and employment level in the hard coal mining sector. This led to a precedent situation when Poland became an importer of this energy carrier. In addition, the European Union’s requirements for greenhouse gas emissions must be taken into account. In connection with the above, it is necessary to search for new energy sources or technologies that enable hard coal to meet the requirements. It is possible to apply the so-called clean coal technologies that allow the greenhouse gas emissions generated during coal combustion to be reduced. As of today, they are not used on a mass scale, because the use of this type of technology involves additional financial expenses. However, taking into account that technologies have been growing faster and faster, are modernized in a shorter time, making a breakthrough discovery took hundreds of years, now it is often a few months, clean coal technologies can become the optimal solution in the near future. It is also necessary to diversify the sources of obtaining imported energy carriers. The article describes coal and crude oil in terms of their mutual substitution. The article is a continuation of research conducted by the authors. Previous publications presented considerations on analogous topics related to natural gas and renewable energy sources. The crude oil market in Poland was analyzed and forecasts for oil extraction and the demand in the world and Poland by 2023 were presented. The SARIMA model was also created. The model made it possible to obtain oil an prices forecast.
During four Polish Geodynamical Expeditions to West Antarctica between 1979 and 1991, seismic measurements were made along 21 deep refraction profiles in the Bransfield Strait and along the coastal area of Antarctic Peninsula using explosion sources. Recordings were made by 16 land stations and 8 ocean bottom seismometers. Good quality recordings were obtained up to about 250 km distance. This allowed a detailed study of the seismic wave field and crustal structure. Three-dimensional tomographic inversion was carried out using first arrivals from the complete data set including off-line recordings. As a result, we obtained a 3-D model of the P-wave velocity distribution in the study area. In the area adjacent to the Antarctic Peninsula coast, sedimentary cover of 0.2 to 3 km thickness was found, whereas in the shelf area and in the Bransfield Strait sedimentary basins with thickness from 5 to 8 km were observed. In the Bransfield Strait a high velocity body with Vp > 7.5 km/s was found at 12 km depth. The use of the off-line data allowed for determination of the horizontal extent of the body. The thickness of the crust varies from more than 35-40 km in the coastal area south of the Hero Fracture Zone to 30-35 km in the area of Bransfield Strait and South Shetland Islands and about 12 km in the Pacific Ocean NW of South Shetland Islands.
Philip Sabin points out that modern wargames not only contain substantial amounts of historical information but also arrange it into interactive models which depict historical processes in a simplified manner. Such models can be used in historical research as well, complementing the discourse through more holistic and mathematically strict accounts, and providing tools that impose some discipline on counter- factual speculation.
The objective of this work was to generate a series of equations to describe the voltinism of Lobesia botrana in the quarantine area of the main winemaking area of Argentina, Mendoza. To do this we considered an average climate scenario and extrapolated these equations to other winegrowing areas at risk of being invaded. A grid of 4 km2 was used to generate statistics on L. botrana captures and the mean temperature accumulation for the pixel. Four sets of logistic regression were constructed using the percentage of accumulated trap catches/grid/week and the degree-day accumulation above 7°C, from 1st July. By means of a habitat model, an extrapolation of the phenological model generated to other Argentine winemaking areas was evaluated. According to our results, it can be expected that 50% of male adult emergence for the first flight occurs at 248.79 ± 4 degree-days (DD), in the second flight at 860.18 ± 4.1 DD, while in the third and the fourth flights, 1671.34 ± 5.8 DD and 2335.64 ± 4.3 DD, respectively. Subsequent climatic comparison determined that climatic conditions of uncolonized areas of Cuyo Region have a similar suitability index to the quarantine area used to adjust the phenological model. The upper valley of Río Negro and Neuquén are environmentally similar. Valleys of the northwestern region of Argentina showed lower average suitability index and greater variability among SI estimated by the algorithm considered. The combination of two models for the estimation of adult emergence time and potential distribution, can provide greater certainties in decision-making and risk assessment of invasive species.
BIM (Building Information Modelling) is a tool and technology closely related to the planning, design, implementation and management of construction investments – both at the level of a building, as well as infrastructure or civil engineering. It combines advanced spatial modeling (using virtual representations of building elements) with management of information at every level, from the modelling of building’s components, through complex interactions between these elements, to the description of building processes and the behavior of users of the building. This is just a part of many possibilities, the full application depends only on the needs and skills of the system user. Construction dependencies are set at the level of the IFC (Industry Foundation Class) universal standard IFC, its syntax allows to describe not only the physical structure of the object, but also their mutual interactions. This is done in a hierarchical way, i.e. from the superior element there are subsequent, lower-level elements and interactions. So how can this tool be used in urban revitalization? The basic problem here is the excess of information related to and contained in the virtual model. In urban planning and design, most of this data is unnecessary. On the other hand, the data contained in the GIS (Geographic Information System) models, despite correlation with external databases, are insufficient. Basic location data, technical conditions of facilities and infrastructure, property dependencies are not enough to obtain a full picture of the urban space. The solution to the problem of linking these systems is CIM (City Information Modeling). It combines the description of an object derived from IFC with database support at the level of GIS systems. Such a broad approach allows for placing enough information in one virtual space for designing, modeling and analyzing urban space. The article is an attempt to demonstrate what conditions must be met by the CIM system, to extend its functionality to issues related to the revitalization of urban areas: whether and how the information contained in the spatial model can be used to determine the rules for the revitalization of space at the urban level?
The study concerns modeling and simulation of the growth of biofilms with heterogeneous structures with a discrete mathematical model based on theory of cellular automata. The article presents two-dimensional density distributions of biofilms for microbial processes: oxidation of ammonium by Nitrosomonas europaea bacteria and glucose utilization by Pseudomonas aeruginosa bacteria. The influence of limiting substrate concentration in the liquid phase on biofilm structure was determined. It has been shown that the value of death rate coefficient of microorganisms has the qualitative and quantitative influence on the density and porosity of the biofilm.
This paper presents results of a research on the possibilities of applying 3D printed casting models for small production series as alternative to traditional tooling production on automated DisaMatch mould production lines. The main task was to verify and compare the dimensions of the 3D printed models before and after moulding process. The paper discusses main advantages and disadvantages of the 3D printing methods used like FDM (Fused Deposition Modeling)/FFF (Fused Filament Fabrication), SLA (stereolitography) and DPP (Daylight Polymer Printing). Measurement of casting model outside dimension change resulting from moulding sand friction on their surface was made with the use of GOM INSPECT software on the basis of 3D scans made with ATOS TripleScan optical scanner. Hardness of 3D printed models made of ABS, Z-ULTRAT, three different photopolymer resins (from FormLab and Liquid Crystal companies) was verified. The result of the research printed models usability for the foundry industry was presented.