Wyniki wyszukiwania

Filtruj wyniki

  • Czasopisma
  • Autorzy
  • Słowa kluczowe
  • Data
  • Typ

Wyniki wyszukiwania

Wyników: 36
Wyników na stronie: 25 50 75
Sortuj wg:

Abstrakt

This paper focuses on the thermal behavior of the starch-based binder (Albertine F/1 by Hüttenes-Albertus) used in foundry technology of molding sand. The analysis of the course of decomposition of the starch material under controlled heating in the temperature range of 25-1100°C was conducted. Thermal analysis methods (TG-DTG-DSC), pyrolysis gas chromatography coupled with mass spectrometry (Py-GC/MS) and diffuse reflectance spectroscopy (DRIFT) were used. The application of various methods of thermal analysis and spectroscopic methods allows to verify the binder decomposition process in relation to conditions in the form in both inert and oxidizing atmosphere. It was confirmed that the binder decomposition is a complex multistage process. The identification of CO2 formation at set temperature range indicated the progressive process of decomposition. A qualitative evaluation of pyrolysis products was carried out and the course of structural changes occurring in the presence of oxygen was determined based on thermo-analytical investigations the temperature of the beginning of binder degradation in set condition was determined. It was noticed that, significant intensification of Albertine F/1 sample decomposition with formation of more degradation products took place at temperatures above 550ºC. Aromatic hydrocarbons were identified at 1100ºC.
Przejdź do artykułu

Abstrakt

The article presents the results of research concerning to AlCu4MgSi alloy ingots produced using horizontal continuous casting process. The presented research was focused on the precise determination of phase composition of the precipitates formed during the solidification of ingots and the analysis of their thermal stability. In order to assess the morphology of precipitates in the AlCu4MgSi alloy, data obtained by using a computer simulation of thermodynamic phenomena were compiled with results obtained using advanced research techniques, i.e. High-temperature X-ray diffraction (HT-XRD), SEM-EDS, Thermal and derivative analysis (TDA) and Glow discharge optical emission spectroscopy (GD OES). SEM observations and analysis of chemical composition in micro-areas showed that the precipitates are mainly intermetallic θ-Al2Cu and β-Mg2Si phases, and also presence of Al19Fe4MnSi2 intermetallic phase was confirmed by X-ray diffraction studies. Based on the prepared Thermo-Calc simulation data, high-temperature X-ray diffraction measurements were conducted.
Przejdź do artykułu

Abstrakt

Płukanie jest operacją technologiczną pozwalającą na usunięcie z kruszyw minerałów ilastych. Z roku na rok ilość szlamów powstających podczas płukania kruszyw wzrasta. Poza rekultywacją obszarów kopalni, nie ma powszechnej metody utylizacji tych odpadów. Możliwość użycia szlamów z płukania kruszyw wapiennych w ceramice budowlanej może być przyjazną środowisku metodą ich wykorzystania. W artykule przedstawiono wybrane badania laboratoryjne dwóch szlamów z płukania kruszywa: dolomitowego i wapiennego. Odpady scharakteryzowano pod względem zawartości wody, składu granulometrycznego (analiza sitowa i areometryczna), chemicznego (XRF) i mineralnego (XRD), właściwości termicznych (STA/EGA, dylatometria, mikroskopia wysokotemperaturowa) oraz trwałości spieków w obecności pary wodnej. Stwierdzono, że odpad z płukania kruszywa dolomitowego zawiera więcej minerałów ilastych i mniej węglanów oraz jest bardziej drobnoziarnisty niż odpad z płukania wapienia. Odpad z płukania kruszywa wapiennego charakteryzują duże wahania zawartości wody i duża zawartość potencjalnie niebezpiecznych ziaren kalcytu. Podczas ogrzewania wysuszonych próbek szlamów do 1300°C zachodzi dekarbonatyzacja i spiekanie. Odpad z płukania kruszywa dolomitowego mięknie, topi się i płynie przed osiągnięciem temperatury 1300°C. Po wypaleniu szlamów w 1000°C spiek ze szlamu wapiennego nie jest odporny na działanie pary wodnej. Odpad z płukania kruszywa dolomitowego może być wykorzystany w ceramice budowlanej bez jego przetwarzania jako podstawowy składnik mas ceramicznych. Odpad z płukania kruszywa wapiennego nie nadaje się do zastosowania w ceramice budowlanej bez jego poprzedniego zmielenia. Jego właściwości sugerują możliwość zastosowania go jedynie jako dodatek do mas ceramicznych, nie jako ich główny składnik.
Przejdź do artykułu

Abstrakt

An overview of the bibliography regarding the connection of knowledge about precious metal alloys and aspects of the use of computer aided technologies to the optimization of the jewelry casting processes is presented. An analysis of the usability of selected CAx systems was made: 1) for spatial design, called Rhinoceros 6 and 2) CAE system: NovaFlow & Solid (NF&S). The authors describe own research including data acquisition and evaluation of temperature variations during solidification of the selected Au-Ag-Cu alloy, with the identification of the phase transformations of this alloy. The intensity of heat exchange was changed (cooling of specimens under ambient temperature conditions – "normal" intensity and with the furnace – very slow cooling). The problem of completing the simulation database was pointed out and analyzed. Examples of simulations of casting selected jewelry (ring and signet) were given and compared with the result of the experiment realized in real conditions. It was confirmed that the optimization by combining experimental and simulation studies allows for the acquisition of new knowledge, and also facilitates the creation of new artistic designs of jewelry as well as performing the feasibility check, and then optimizing the chosen technology.
Przejdź do artykułu

Abstrakt

Thermodynamic analysis of car air cooler is presented in this paper. Typical refrigerator cycles are studied. The first: with uncontrolled orifice and non controlled compressor and the second one with the thermostatic controlled expansion valve and externally controlled compressor. The influence of the refrigerant decrease and the change of the air temperature which gets to exchangers on the refrigeration efficiency of the system; was analysed. Also, its effectiveness and the power required to drive the compressor were investigated. The impact of improper refrigerant charge on the performance of air conditioning systems was also checked.
Przejdź do artykułu

Abstrakt

Waste disposal is imposed by the European Union under Treaty of Accession concerning waste management order. One of the waste disposal methods is thermal utilisation. The paper presents an investigation of sewage sludge briquettes used as a fuel in combustion process. The research study was carried out on samples taken from the Municipal Wastewater Treatment Plant in Bochnia. Briquettes with lime were formed. The analysis of the elementary chemical composition of municipal sewage sludge, the composition of the ash and thermogravimetric analysis were carried out. The results indicate that the prepared briquettes had sufficient fuel properties.
Przejdź do artykułu

Abstrakt

There has been a growing interest in the peritectic due to increasing productivity, quality, and alloy development. Differential scanning calorimetry (DSC) has traditionally been used to study steel solidification but suffers significant limitations when measuring the solidus and peritectic. This work covers a new thermal analysis system that can characterize the peritectic reaction. Heats of AISI/SAE 1030 and 4130 steel were poured to provide some benchmarking of this new technique. The peritectic was detected and the reaction temperature measured. Measurements agree reasonably well with reference information. A review of the literature and thermodynamic calculations did find some disagreement on the exact temperatures for the peritectic and solidus. Some of this difference appears to be related to the experimental techniques employed. It was determined that the system developed accurately indicates these reaction temperatures. The system provides a unique method for examining steel solidification that can be employed on the melt deck.
Przejdź do artykułu

Abstrakt

During the slag refining process, in the real systems, the complex processes of mass exchange appear. Some relations between the stimulators in the environment - slag - metal system allow to initiate mass exchange reactions in the process of slag refining. Due to this kind of influences there is a possibility of direction and control of melting copper and it’s alloys.
Przejdź do artykułu

Abstrakt

This work presents an influence of cooling rate on crystallization process, structure and mechanical properties of MCMgAl12Zn1 cast magnesium alloy. The experiments were performed using the novel Universal Metallurgical Simulator and Analyzer Platform. The apparatus enabled recording the temperature during refrigerate magnesium alloy with three different cooling rates, i.e. 0.6, 1.2 and 2.4°C/s and calculate a first derivative. Based on first derivative results, nucleation temperature, beginning of nucleation of eutectic and solidus temperature were described. It was fund that the formation temperatures of various thermal parameters, mechanical properties (hardness and ultimate compressive strength) and grain size are shifting with an increasing cooling rate.
Przejdź do artykułu

Abstrakt

The problem of harmful casting resins has been present in foundries for many years. Manufacturers are introducing new products that contain in their composition environmentally and eco-friendly ingredients. Unfortunately, not all types of technology can be used, sometimes environmental benefits are disproportionate to the quality of castings and their price. In the foundry industry, the most popular binders are based on organic compounds (often carcinogenic) and other harmful substances. Due to strict legal regulations regarding environmental protection, as well as care for the foundry's workers' comfort - their occurrence should be reduce to a minimum. These compounds often behave also depending on the conditions of use (temperature, atmosphere). The application of various methods of thermal analysis and spectroscopic methods allows to verify the mechanism of resin decomposition process in relation to conditions in the form in both inert and oxidizing atmosphere. For analysis the resins from cold-box technology, were used TG–DTG–DSC, Py-GC/MS methods and specified the course of changes occurring in combination of different atmosphere.
Przejdź do artykułu

Abstrakt

Anisotropic rotor configurations influenced by the presence of a large number of geometrical parameters in a permanent magnet assisted synchronous reluctance (PMASR) motor pose design challenges in obtaining a robust geometry satisfying the requirements of reduced torque ripple and high torque density. Therefore, the purpose of this work is to perform detailed geometrical sensitivity analysis of a 36 slot/4 pole permanent magnet assisted synchronous reluctance (PMASR) motor using h-indexing and level sensitivity analysis in order to specify a guideline for designers to prioritize the design variables for optimization. Systematic multi-level design optimization for multiple objectives is implemented by an NSGA-II algorithm aided by the finite element analysis tool, hardware prototyping and experimental validation. The optimized designs also exhibit better structural and thermal characteristics.
Przejdź do artykułu

Abstrakt

The thermal reclamation process as a utilisation method of spent moulding and core sands is more costly than other reclamation methods, but in the majority of cases it simultaneously provides the best cleaning of mineral matrices from organic binders. Thus, the application of the thermal analysis methods (TG-DSC), by determining the temperature range within which a degradation followed by a destruction of bounded organic binders in moulding sands, can contribute to the optimisation of the thermal reclamation process and to the limiting its realisation costs. The thermal analysis results of furan resin, one of the most often applied binder in foundry practice, are presented in the hereby paper. The influence of the heating rate of the sample - placed in the thermal analyser - on its degradation and destruction process under oxygen-free (argon) and oxygen (air) conditions, were compared. The recorded TG and DSC curves were used for analysing these processes as the temperature as well as the time function. The obtained results were analysed with regard to determining the required temperature of the thermal reclamation of the investigated organic binder. The usefulness of the developed methodology was found out, however under conditions of meeting several essential requirements concerning the repeatability of performed analyses.
Przejdź do artykułu

Abstrakt

A lumped parameter type code, called HEPCAL, has been worked out in the Institute of Thermal Technology of the Silesian University of Technology for simulations of a pressurized water reactor containment transient response to a loss-of-coolant accident. The HEPCAL code has been already verified and validated against available experimental data, which in fact have been taken from separate effect tests mainly. This work is devoted to validation of the latest version of the HEPCAL code against experimental data from more complex tests. These experiments have been performed on three different test rigs (called TOSQAN,MISTRA and ThAI) and a part of them became the basis of the International Standard Problem No. 47 (ISP-47) dedicated to containment thermal-hydraulics. Selected experiments realized within the framework of the ISP-47 project have been simulated using the HEPCAL-AD code. The obtained results allowed for drawing of some important conclusions concerning heat and mass transfer models (especially steam condensation), two-phase flow model and buoyancy effects.
Przejdź do artykułu

Abstrakt

The paper presents the results of thermoanalytical studies by TG/DTG/DTA, FTIR and GC/MS for the oil sand used in art and precision foundry. On the basis of course of DTG and DTA curves the characteristic temperature points for thermal effects accompanying the thermal decomposition reactions were determined. This results were linked with structural changes occurred in sample. It has been shown that the highest weight loss of the sample at temperatures of about 320°C is associated with destruction of C-H bonds (FTIR). In addition, a large volume of gases and high amounts of compounds from the BTEX group are generated when liquid metal interacts with oil sand. The results show, that compared to other molding sands used in foundry, this material is characterized by the highest gaseous emissions and the highest harmfulness, because benzene emissions per kilogram of oil sand are more than 7 times higher than molding sand with furan and phenolic binders and green sand with bentonite and lustrous carbon carrier.
Przejdź do artykułu

Abstrakt

In the dissertation it has been shown, that so called “time-thermal treatment” (TTT) of the alloy in liquid state as overheating the metal with around 250o C above Tliq. and detailing it in temperature for 30 to 40 minutes has the influence on changing the crystallization parameters (Tliq., TEmin. , TEmax., TE(Me), TSol.). It was ascertained, that overheating the AlSi17Cu5Mg alloy substantially above Tliq. results with microcrystalline structure. Evenly distributed in the eutectic warp primeval silicon crystals and supersaturated with alloying additives of base content (Cu, Mg, Fe) of α(Al) solution, ensures not only increase durability in ambient temperature, but also at elevated temperature (250o C), what due to it’s use in car industry is an advantage.
Przejdź do artykułu

Abstrakt

Superalloys show a good combination of mechanical strength and resistance to surface degradation under the influence of chemically active environments at high temperature. They are characterized by very high heat and creep resistance. Their main application is in gas turbines, chemical industry, and in all those cases where resistance to creep and the aggressive corrosion environment is required. Modern jet engines could never come into use if not for progress in the development of superalloys. Superalloys are based on iron, nickel and cobalt. The most common and the most interesting group includes superalloys based on nickel. They carry loads at temperatures well in excess of the eighty percent of the melting point. This group includes the H282 alloy, whose nominal chemical composition is as follows (wt%): Ni - base, Fe - max. 1.5%, Al - 1.5% Ti - 2.1%, C - 0.06% Co - 10% Cr - 20% Mo - 8.5%. This study shows the results of thermal analysis of the H282 alloy performed on a cast step block with different wall thickness. Using the results of measurements, changes in the temperature of H282 alloy during its solidification were determined, and the relationship dT / dt = f (t) was derived. The results of the measurements taken at different points in the cast step block allowed identifying a number of thermal characteristics of the investigated alloy and linking the size of the dendrites formed in a metal matrix (DAS) with the thermal effect of solidification. It was found that the time of solidification prolonged from less than ome minute at 10 mm wall thickness to over seven minutes at the wall thickness of 44 mm doubled the value of DAS.
Przejdź do artykułu

Abstrakt

Suitability of the given binding agent for the moulding sands preparation depends on the one hand on the estimation of technological properties of the sand and the mould made of it and the obtained casting quality and on the other hand on the assessment of this sand influence on the natural and working environment. Out of moulding sands used in the foundry industry, sands with organic binders deserve a special attention. These binders are based on synthetic resins, which ensure obtaining the proper technological properties and sound castings, however, they negatively influence the environment. If in the initial state these resins are not very dangerous for people and for the environment, thus under an influence of high temperatures they generate very harmful products, being the result of their thermal decomposition. Depending on the kind of the applied resin (phenol-formaldehyde, urea, furfuryl, urea–furfuryl, alkyd) under an influence of a temperature such compounds as: furfuryl alcohol, formaldehyde, phenol, BTEX group (benzene, toluene, ethylbenzene, xylene), and also polycyclic aromatic hydrocarbons (PAH) can be formed and released. The aim of the study was the development of the method, selection of analytical methods and the determination of optimal conditions of formation compounds from the BTEX group. An emission of these components constitutes one of the basic criteria of the harmfulness assessment of binders applied for moulding and core sands. Investigations were carried out in the specially designed set up for the thermal decomposition of organic substances in a temperature range: 5000 C – 13000 C at the laboratory scale. The object for testing was alkyd resin applied as a binding material for moulding sands. Within investigations the minimal amount of adsorbent necessary for the adsorption of compounds released during the decomposition of the resin sample of a mass app. 15 mg was selected. Also the minimal amount of solvent needed for the desorption of compounds adsorbed in the column with adsorbent was found. The temperature range, in which the maximal amounts of benzene, toluene, ethylobenzene and xylenes are released from the resin, was defined. The qualitative and quantitative analyses of compounds from the BTEX group were performed by means of the gas chromatography combined with the mass spectrometry (GC/MS).
Przejdź do artykułu

Abstrakt

The results of investigations of spent moulding sands taken from the mould in which the metal core cooling system - to increase the cooling rate of the ladle casting - was applied, are presented in the hereby paper. The changes of the spent moulding sand at the casting external side being the result of degradation and destruction processes of organic binder, were analysed in this publication. Since the reclaimed material, obtained as a result of the mechanical reclamation of spent sands of the same type, is used as a grain matrix of the moulding sand, the amount of a binder left from the previous technological cycle is essential for the sound castings production. On the bases of investigations of the thermal analysis, ignition losses, dusts contents and pH values of the samples taken from the spent sand the conditions under which the process of gases displacing in the casting mould was realised as well as factors limiting the efficient mould degassing - were considered in this study. The possible reason of a periodical occurrence of an increased number of casting defects due to changing gas volume emission, being the reason of the realised technological process, was indicated.
Przejdź do artykułu

Abstrakt

The conducted work shows and confirms how thermal analysis of grey and ductile iron is an important source for calculating metallurgical data to be used as input to increase the precision in simulation of cooling and solidification of cast iron. The aim with the methodology is to achieve a higher quality in the prediction of macro– and micro porosity in castings. As comparison objects standard type of sampling cups for thermal analysis (solidification module M ≈ 0.6 cm) is used. The results from thermal analysis elaborated with the ATAS MetStar system are evaluated parallel with the material quality (including tendency to external and internal defects) of the tested specimen. Significant temperatures and calculated quality parameters are evaluated in the ATAS MetStar system and used as input to calibrate the density curve as temperature function in NovaFlow&Solid simulation system. The modified data are imported to the NovaFlow&Solid simulation system and compared with real results.
Przejdź do artykułu

Abstrakt

The paper presents a research results concerning impact of volume modification (ceramic filter containning cobalt aluminate and hafniumpowder) and simultaneous surface and volume modification on solidification and stereological parameters of macrostructure of castingsmade from post-production scrap of nickel superalloy IN-713C. Research included investigation of the influence of chemical compositionon the temperature Tliq i Tsol and evaluation of following macrostructure parameters: the number of grains per mm2, average grain area andshape coefficient. Results indicate high influence of carbon content on Tliq. Macrostructure of sample castings indicate positive effect of surface and volume modification, however impact of surface modification is more pronounced.
Przejdź do artykułu

Abstrakt

This paper presents and discusses the mathematical model of thermal phenomena occurring in axis-symmetric electromechanical linear motion converters. On the basis of the developed model, software to analyze the process of the heating up of this type of converters, was created. The effect of the thickness and type of material of the slot insulation, as well as the speed of the runner on the temperature distribution in the analyzed object was examined in-depth. Selected results of simulated calculations have been presented.
Przejdź do artykułu

Abstrakt

The paper deals with the influence of manganese in AlSi7Mg0.3 alloy with higher iron content. Main aim is to eliminate harmful effect of intermetallic – iron based phases. Manganese in an alloy having an iron content of about 0.7 wt. % was graded at levels from 0.3 to 1.4 wt. %. In the paper, the effect of manganese is evaluated with respect to the resulting mechanical properties, also after the heat treatment (T6). Morphology of the excluded intermetallic phases and the character of the crystallisation of the alloy was also evaluated. From the obtained results it can be concluded that the increasing level of manganese in the alloy leads to an increase in the temperature of the β-Al5FeSi phase formation and therefore its elimination. Reducing the amount of β-Al5FeSi phase in the structure results in an improvement of the mechanical properties (observed at levels of 0.3 to 0.8 wt. % Mn). The highest addition of Mn (1.4 wt.%) leads to a decrease in the temperature corresponding to the formation of eutectic silicon, which has a positive influence on the structure, but at the same time the negative sludge particles were also present
Przejdź do artykułu

Abstrakt

The work presents results of solution combustion method utilization for yttria (Y2O3) nanopowder fabrication. Experiments were carried out with four different reducing agents: urea, glycine, citric acid and malonic acid added in stoichiometric ratio. The reactions were investigated using simultaneous DSC/DTA thermal analysis. After synthesis the reaction products were calcined at temperature range of 800-1100°C and analyzed in terms of particle size, specific surface area and morphology. Best results were obtained for nanoyttria powder produced from glycine. After calcination at temperature of 1100°C the powder exhibits in a form of nanometric, globular particles of diameter <100 nm, according to SEM analysis. The dBET for thus obtained powder is 104 nm, however the powder is agglomerated as the particle size measured by dynamic light scattering analysis is 1190 nm (dV50).
Przejdź do artykułu

Abstrakt

In this article, there were presented results of research on influence of reclamation process on the ecological quality of reclaim sand with furan resin used in nonferrous foundry. The quality of reclaimed sand is mainly define by two group of chemical substances from elution of reclaimed sand: Dissolves Organic Carbon (DOC) and Total Dissolves Solids (TDS). Reclaimed sand used in test was prepared in experimental thermal reclaimer and mechanical vibration reclaimer REGMAS installed in Faculty of Foundry Engineering at University of Science and Technology in Krakow. The reference point is molding sand shaking out and crumble in jaw crusher. Test of elution was made in acreditation laboratory in Center For Research and Environmental Control in Katowice up to the standard with Dissolves Organic Carbon (DOC) - PN-EN 1484:1999; Total Dissolves Solids (TDS) - PN-EN 15216:2010. The standard for elution test is PN-EN 12457- 4:2006. Except that we were made loss of ignition test, to check how many resin was rest on sand grains.
Przejdź do artykułu

Abstrakt

The article presents results of studies of silicon – molybdenum cast iron (4.42% Si, 2.59% Mo and 2.48% C wt.-%) crystallization process. Metallographic analysis was carried out using SEM-scanning electron microscopy with the EDS system. In order to determine the phase composition, X-ray diffraction studies were performed. Thermo-Calc, a computer simulation program, was used to simulate the crystallization process. . The obtained data allowed to describe the effect of some elements on the crystallization process. The silicon phase of MnSi could not be identified during metallographic studies. Also, computer simulation of the crystallization process did not answer the question at which point the silicon phase of MnSi crystallizes in the tested alloy. Therefore, not all results obtained were linked to the registered crystallization process (TDA process). The EDS analysis revealed an unusual distribution of molybdenum in the microstructure of the sample, where it is clearly visible that the area enriched with this element is also the separation of spheroidal graphite. The possibility of occurrence of Mo-rich micro-areas found in graphite is considered. The case is debatable and difficult to resolve at this stage. Perhaps, at such a high concentration of molybdenum (2.59% Mo) in the alloy, conditions are created for simultaneously crystallization of graphite and molybdenum phases.
Przejdź do artykułu

Ta strona wykorzystuje pliki 'cookies'. Więcej informacji