Search results

Filters

  • Journals
  • Date

Search results

Number of results: 9
items per page: 25 50 75
Sort by:

Abstract

In this study, silicon carbide (SiC) reinforced lead-free solder (SAC305) was prepared by the powder metallurgy method. In this method SAC305 powder and SiC powder were milled, compressed and sintered to prepare composite solder. The composite solders were characterized by optical and scanning electron microscopy for the microstructural investigation and mechanical test. Addition of 1.5 wt. % and 2 wt. % ceramic reinforcement to the composite increased compressive strengths and microhardness up to 38% and 68% compared to those of the monolithic sample. In addition, the ceramic particles caused an up to 55% decrease in the wetting angle between the substrate and the composite solder and porosity was always increased with increase of SiC particles.
Go to article

Abstract

Cast magnesium matrix composites reinforced with silicon carbide particles were investigated by using Raman microscopy. 3C, 4H and 6H polytypes of SiC particles were identified in the investigated composites. Additionally, Mg2Si compound was detected by Raman microscopy in the composites microstructure.
Go to article

Abstract

The paper presents a study of the performance of some selected UV detectors. Unlike many similar works, the obtained data refer to commercial photodiodes (not only to detector materials). The main task of the research was to determine the influence of the operating temperature and annealing on the detector spectral responsiveness. A comparison of the results obtained for the photodiodes made of GaN and SiC was also performed. Although both kinds of detectors can work at high temperatures for a long time, some modification of their properties was observed. However, for GaN and SiC photodiodes, this modification has a substantially different nature. It is very important for some applications, e.g. fire alarms and a military equipment.
Go to article

Abstract

The techniques of micro and nano structurization of surfaces of various materials are utilized in electronics and medicine. Such procedure as wet and dry etching allows to fabricate protruded or recessed micro and nanostructures on the surface. In the paper some examples of utilization of a surface structurization, known from literature, are described. Some structurization methods and experimental results for fabrication of the arrays of sharp microtips are presented. Wet and/or dry etching, and thermal oxidation process were used to form the arrays of sharp gated and non-gated, protruded or recessed silicon microtips on silicon wafer. For the first time, the arrays of silicon carbide (SiC) microtips on glass wafer have been produced by use of the transfer mold technique. Arrays of sharp microtips are used as field electron emission cathodes for vacuum microelectronics devices. Some electron emission measurements for these cathodes have been carried out. New application of silicon microtips array in biochemistry has been tested with satisfactory results.
Go to article

Abstract

The presented work deals with the influence of the addition of soft graphite particles on the abrasive wear of composite reinforced with hard SiC particles. The discussed hybrid composites were produced by stirring the liquid alloy and simultaneous adding the mixture of particles. The adequately prepared suspension was gravity cast into a metal die. Both the composite castings obtained in this way and the comparative castings produced of the pure matrix alloy were examined for the abrasive wear behaviour. Photomacrographs of the sliding surfaces of the examined composites were taken, and also the hardness measurements were carried out. It was found that even a small addition of Cgr particles influences positively the tribological properties of the examined composite materials, protecting the abraded surface from the destructive action of silicon carbide particles. The work presents also the results of hardness measurements which confirm that the composite material hardness increases with an increase in the volume fraction of hard reinforcing particles.
Go to article

Abstract

Light weight, low density with high mechanical properties and corrosion resistance, aluminum is the most important material and is commonly used for high performance applications such as aerospace, military and especially automotive industries. The researchers who participate in these industries are working hard to further decrease the weight of end products according to legal boundaries of greenhouse gases. A lot of research was undertaken to produce thin sectioned aluminum parts with improved mechanical properties. Several alloying element addition were investigated. Yet, nowadays aluminum has not met these expectations. Thus, composite materials, particularly metal matrix composites, have taken aluminum’s place due to the enhancement of mechanical properties of aluminum alloys by reinforcements. This paper deals with the overview of the reinforcements such as SiC, Al2O3 and graphene. Graphene has recently attracted many researcher due to its superior elastic modulus, high fatigue strength and low density. It is foreseen and predicted that graphene will replace and outperform carbon nanotubes (CNT) in near future.
Go to article

Abstract

This work summarizes efficiency measurement results of a full bridge, 3 phase inverter composed of state-of-the-art Si IGBT transistors and Si or SiC diodes. Different (symmetrical and discontinuous) space vector modulation strategies were chosen in order to examine their influence (together with modulation frequency) on inverter losses. Induction machine was used as load, different load points were examined. Results clearly show, that proper modulation strategy, minimizing the switching losses of semiconductor switches, can increase the overall output efficiency at about 1% in case of both silicon and hybrid constructions. The drawback of DPWM approach is connected with the decreased quality of inverter output current. Hybrid technology can also improve the output efficiency at about 1% when compared to traditional constructions, but only in case of elevated switching frequencies. At low frequencies (below 10 kHz) modern semiconductor offer comparable results at much lower device costs.
Go to article

Abstract

The gas-tungsten arc (GTA) welding behaviors of a magnesium matrix composite reinforced with SiC particles were examined in terms of microstructure characteristics and process efficiencies. This study focused on the effects of the GTAW process parameters (like welding current in the range of 100/200 A) on the size of the fusion zone (FZ). The analyses revealed the strong influence of the GTA welding process on the width and depth of the fusion zone and also on the refinement of the microstructure in the fusion zone. Additionally, the results of dendrite arm size (DAS) measurements were presented.
Go to article

Abstract

The AlMg10 aluminum alloy reinforced with SiC particles was subjected to friction stir processing (FSP). The composite was made by mechanical mixing and gravity casting. The mass fraction of SiC particles in the composite was about 10%. Evaluation of the effects of FSP treatment was performed by means of light microscopy, scanning electron microscopy, EDS and hardness measurement. It was found that the inhomogeneous distribution of SiC particles and their agglomeration, which were observable in the cast composite, were completely eliminated after FSP modification. The treatment was also accompanied by homogenisation of the material in the mixing zone as well as fragmentation of both the matrix grain of the composite and SiC particles. In the case of SiC particles, a change in their shape was also observed. In the as-cast composite, particles with dimensions from 30 to 60 µm and a sharp-edged polyhedral shape prevailed, while in the material subjected to friction treatment, particles with dimensions from 20 to 40 µm and a more equiangular shape prevailed. Pores and other material discontinuities occurring frequently in the as-cast composite were completely eliminated after friction modification. The recorded changes in the microstructure of the material were accompanied by an increase in the hardness of the composite by nearly 35%. The conducted investigations have shown that FSP modification of the AlMg10/SiC composite made by the casting method leads to favorable microstructural changes in the surface layer and may be an alternative solution to other methods and technologies used in surface engineering.
Go to article

This page uses 'cookies'. Learn more