The aim of this paper is to present an assessment of the slip influence on the deflection of the steel plate-concrete composite beams, which are a new type of a design concept. The proposed method is based on the procedure included in the PN-EN 1992-1-1, which has been modified with taking into consideration interface slip. The theoretical analysis was verified by experimental studies.
In this stud y, we attempt to analyse free nonlinear vibrations of buckling in laminated composite beams. Two new methods are applied to obtain the analytical solution of the nonlinear governing equation of the problem. The effects of different parameters on the ratio of nonlinear to linear natural frequencies of the beams are studied. These methods give us an agreement with numerical results for the whole range of the oscillation amplitude.
Introduction of polymers into the cement composites improves same of the properties of concretes and mortars. Therefore, the polymer-cement composites are successfully used in construction. The model of microstructure formation in cement composites modified with thermoplastic polymer (pre-mix modifiers) has already been developed and successfully implemented. However, the formation of microstructure in the case of epoxy-cement composites (containing post-mix modifier) demonstrates same peculiarities which should be taken into account when modelling the process. The microstructure of epoxy-cement composites and its formation is discussed in the paper. The model is offered, formulated on the basis of the microscopic observations and results of testing.
During austral summer phytoplankton is the main component of food of E. superba postlarval stages. Diatomeae: Thalassiosira spp., Nitzschia spp. and tiny Pennatae constitue 98% of all consumed food particles. 91% of algae consumed were of 8—40 μm, and their mean size is 21.4 μm. The mean amount of algae found in of Euphausia superba was about 1700 per individual. The differences in species composition and the size of algae eaten by juvenes, preadult and adult individuals decrease the food competition between particular age groups of E. superba.
This paper presents research results of composite tubes filled with self-compacting concrete. The impact of the selected materials and geometric factors on resistance to the vertical shear was evaluated in this study. The resistance of the tested members was compared with recommendations given in Eurocode PN-EN 1994-1-1. From the results obtained in the tests it can be deduced that more parameters should be taken into consideration when determining resistance to the vertical shear in the interface between steel and concrete than PN-EN 1994-1-1 recommends.
This paper presents an experimental analysis of flexural capacity and deformability of structural concrete slabs prepared as composite members consisting of two concrete layers made of reinforced ordinary concrete (N) and fiber reinforced concrete (SFRC). The reinforced concrete composite slabs used in the tests were prepared in the dimensions of 600 x 1200 x 80 mm. The basis was composed of two layers consisting of SFRC, one as the top layer, and one as ordinary concrete. The results of the analysis confirm a significant improvement of structural properties of the composite slab in comparison to the slabs prepared wholly of ordinary concrete.
The use of biomass in the energy industry is the consequence of ongoing efforts to replace Energy from fossil fuels with energy from renewable sources. However, due to the diversity of the biomass, its use as a solid fuel generates waste with diverse and unstable chemical composition. Waste from biomass combustion is a raw material with a very diverse composition, even in the case of using only one type of biomass. The content of individual elements in fly ash from the combustion of biomass ranges from zero to tens of percent. This makes it difficult to determine the optimal recovery methods. The ashes from the combustion of biomass are most commonly used in the production of building materials and agriculture. This article presents the elemental composition of the most commonly used biomass fuels. The results of the analysis of elemental composition of fly ashes from the combustion of forest and agricultural biomass in fluidized bed boilers used in the commercial power industry were presented. These ashes are characterized by a high content of calcium (12.3–19.4%), silicon (1.2–8.3%), potassium (0.05–1.46%), chlorine (1.1–6.1%), and iron (0.8–6.5%). The discussed ashes contained no sodium. Aluminum was found only in one of the five ashes. Manganese, chromium, copper, nickel, lead, zinc, sulfur, bismuth, titanium and zirconium were found in all of the examined ashes. The analysis of elemental composition may allow for a preliminary assessment of the recovery potential of a given ash.
Changes in the amount of basic nitrogen fractions (total, protein and non-protein nitrogen) were studied in an annual cycle. Significant seasonal changes were noted, minima occurring in Antarctic winter and maxima during spring-summer season. These changes are due mainly to high fluctuations of water content in krill in the annual cycle.
The paper is concerned with the most fundamental compositional divide to be found in lyrical discourse, consisting in that the latter one is normally split into an empirical part, presenting the author’s concrete experience, and a focal part, where the author discovers some signifi cant truth or/and changes her attitude towards the world. It is claimed in the paper that, more generally, one of the specifi c linguistic properties of focal fragments is their higher and/or specially underscored informativity, and, in particular, one of the means recruited to emphasize it is inverted word order.
The paper presents the response of a three-layered annular plate with damaged laminated facings to the loads acting in their planes. The presented problem concerns the analysis of the combination of global plate failure in the form of buckling with the local micro defects, like fibre or matrix cracks, located in the laminas. The plate structure consists of thin laminated, fibre-reinforced composite facings and a thicker foam core. The matrix and fibre cracks of facings laminas can be transversally symmetrically or asymmetrically located in plate structure. Critical static and dynamic stability analyses were carried out solving the problem numerically and analytically. The numerical results show the static and dynamic stability state of the composite plate with different combinations of damages. The final results are compared with those for undamaged structure of the plate and treated as quasi-isotropic ones. The analysed problem makes it possible to evaluate the use of the non-ideal composite plate structure in practical applications.
Applying the commonly accepted definitions of identity to landscape as our field of research, in particular landscape in protected areas, we assume that identity is the deepest relationship with the landscape (surroundings) perceived by man, with its historical layers of content (the culture and tradition of a place) and form (the canon of a place). An evaluation of change in time should be the keynote of deliberations on place identity. Basing on the current status of research, a review of specialist literature and the author’s experience to date, the above definitions and terms may be referenced to talk about “former” and “new” place identity, especially if we acquiesce to what is termed “the culture of a place” that originates in love for it and willingness to participate in the act of creation that has been launched upon the site. Author tries to explain this fenomenom on example of revitalization, on scale of conntry or even the Europe – the cultural – strategic landscape od Zamość Fortress.
Nematoda, Tardigrada, Rotifera and Crustacea composition in different freshwater habitats on Spitsbergen (Arctic) and King George Island (Antarctic) was presented. In all surveyed groups more genera and species were recorded from Spitsbergen than from King George Island. Habitats richest in taxa were moss banks and thaw ponds, whereas streams were poorest in species. In all groups in both regions cosmopolitan species dominated, but higher number of endemic species was recorded on King George Island. Regarding species composition in surveyed groups it can be suggested that freshwater habitats on Spitsbergen are more similar to each other than those on King George Island.
Changes in body mass and body reserves of Little Auks (Alle alle) were studied throughout the breeding season. Body mass loss after chick hatching was analyzed with respect to two hypotheses: (1) mass loss reflects the stress of reproduction, (2) mass loss is adaptive by reducing power consumption during flight. Body mass of both males and females increased during incubation, dropped abruptly after hatching, and remained stable until the end of the chick-rearing period. These changes were largely due to change in mass of fat reserves. Body mass, fat, and protein reserves, when corrected for body size, did not differ between sexes at the end of incubation. Female size-corrected body mass at that time was correlated with peak body mass of chicks. The estimated energy savings for flight due to the decline in adult body mass after chick hatching were small compared with the total energy expenditure of adults feedings chicks, which did not support hypothesis (2). The contribution to chick feeding was not equal; the ratio of females to males caught with food for chicks was 1.8. Size-corrected body mass during chick-rearing was lower in females, proportional to their higher chick feeding effort compared with males. Females, in contrast to males, lost protein reserves during chick-rearing. Digestive tract mass of adults increased by half throughout the breeding period. These findings supported elements of hypothesis (1). Despite high energy expenditure rates, both sexes had about 10 g of fat reserves at the end of chick feeding. Body mass of both sexes was constant during the greater part of the chick-feeding period. It was suggested therefore that mass loss is regulated with respect to lower fat reserves required during chick-rearing.
Definition of a composite  describes an ideal composite material with perfect structure. In real composite materials, structure is usually imperfect – composites contain various types of defects [2, 3–5], especially as the casted composites are of concern. The reason for this is a specific structure of castings, related to course of the manufacturing process. In case of metal matrix composite castings, especially regarding these manufactured by saturation, there is no classification of these defects [2, 4]. Classification of defects in castings of classic materials (cast iron, cast steel, non-ferrous alloys) is insufficient and requires completion of specific defects of mentioned materials. This problem (noted during manufacturing metal matrix composite castings with saturated reinforcement in Institute of Basic Technical Sciences of Maritime University Szczecin) has become a reason of starting work aimed at creating such classification. As a result, this paper was prepared. It can contribute to improvement of quality of studied materials and, as a consequence, improve the environment protection level.
This paper presents matters related to production of ceramic and cast iron composite. The composite was made with the use of a foam structured ceramic insert. The tests included measuring of hardness, impact strength and resistance to abrasive wear of the composite produced. On the basis of obtaining results was stated that the use of foamed ceramic filters provides good conditions of filling a ceramic framework with molten grey or chromium cast iron. The growth of hardness of the ceramic- grey cast iron composite is ca. 60% as compared to the grey cast iron hardness. The growth of hardness of the ceramic- chromium cast iron composite is slight and does not exceed 5 % in comparison to the chromium cast iron. Introduction of the ceramic inserts deteriorates the cast iron impact strength by ca. 20 - 30 %. The use of ceramic inserts increases the resistance to abrasive wear in case of grey cast iron by ca. 13% and in case of the chromium cast iron by ca. 10 %.
The multiple direct remelting of composites based on the A359 alloy reinforced with 20% of Al2O3 particles was performed. The results of both gravity casting and squeeze casting were examined in terms of the obtained microstructure and mechanical characteristics. In microstructure examinations, the combinatorial method based on phase quanta theory was used. In mechanical tests, the modified low cycle fatigue method (MLCF) was applied. The effects obtained after both gravity casting and squeeze casting were compared. It was noted that both characteristics were gradually deteriorating up to the tenth remelting. The main cause was the occurrence of shrinkage porosity after the gravity casting. Much better results were obtained applying the squeeze casting process. The results of microstructure examinations and fatigue tests enabled drawing the conclusion that the A359 alloy reinforced with Al2O3 particles can confer a much better fatigue life behavior to the resulting composite than the A359 alloy without the reinforcement. At the same time, comparing these results with the results of the previous own research carried out on the composites based also on the A359 alloy but reinforced in the whole volume with SiC particles, it has been concluded that both types of the composites can be subjected to multiple remelting without any significant deterioration of the structural and mechanical characteristics. The concepts and advantages of using the combinatorial and MLCF methods in materials research were also presented
Transverse effective thermal conductivity of the random unidirectional fibre-reinforced composite was studied. The geometry was circular with random patterns formed using random sequential addition method. Composite geometries for different volume fraction and fibre radii were generated and their effective thermal conductivities (ETC) were calculated. Influence of fibre-matrix conductivity ratio on composite ETC was investigated for high and low values. Patterns were described by a set of coordination numbers (CN) and correlations between ETC and CN were constructed. The correlations were compared with available formulae presented in literature. Additionally, symmetry of the conductivity tensor for the studied geometries of fibres was analysed.
Carotenoids in six species of the lichens from Antarctica (Xanthoria eleguns, Caloplaca regalis, Usnea antarctica, U. fasciata, Himantormia lugubris and Ramalina terebrata) have been investigated by means of column and thin — layer chromatography. The following carotenoids were found: β-carotene, α- and β-cryptoxanthin, canthaxanthin. lycophyll, lycoxanthin, lutein, lutein epoxide, zeaxanthin, antheroxanthin, adonixanthin, diatoxanthin, rhodoxanthin, rhodoxanthm derivative, α-doradexanthin, astaxanthin, astaxanthin ester, mutatochrome, mutatoxanthin and cryptoflavin. Most frequently occurred β-carotene, β-cryptoxanthin, lutein epoxide, zeaxanthin and mutatoxanthin. The total carotenoid content ranged from 10.242 (Ramalina terebrata) to 18.700 mg/g dry weight (Himantormia lugubris) in October and from 4.765 (Ramalina terebrata) to 12.462 mg/g dry weight (Caloplaca regalis) in February.
In this study, free and forced vibration responses of carbon nanotube reinforced uniform and tapered composite beams are investigated. The governing differential equations of motion of a carbon nanotube (CNT) reinforced uniform and tapered composite beams are presented in finite element formulation. The validity of the developed formulation is demonstrated by comparing the natural frequencies evaluated using present FEM with those of available in literature. Various parametric studies are also performed to investigate the effect of aspect ratio, percentage of CNT content, ply orientation, and boundary conditions on natural frequencies and mode shapes of a CNT reinforced composite beam. It was observed that the addition of carbon nanotube in fiber reinforced polymer composite (FRP) beam enhances the stiffness of the structure which consequently increases the natural frequencies and alters the mode shapes.
Humic acids, isolated from selected soils of Grønfjorden area (Spitsbergen) were investigated in terms of molecular composition and resistance of decomposition. The degree of soils organic matter stabilization has been assessed with the use of modern instrumental methods (nuclear magnetic resonance spectroscopy (CP/MAS 13C-NMR). Analysis of the humic acids showed that aromatic compounds prevail in the organic matter formed in cryoconites, located on the glaciers surfaces. The predominance of aliphatic fragments is revealed in the soils in tidal zone that form on the coastal terrace. This could be caused by sedimentation of fresh organic matter exhibiting low decomposition stage due to the harsh climate and processes of hydrogenation in the humic acids, destruction of the C-C bonds and formation of chains with a high hydrogen content. These processes result in formation of aliphatic fragments in the humic acids. In general, soils of the studied region characterizes by low stabilized soil organic matter which is indicated by low aromaticity of the HAs.
The study aimed to apply the protection from damage to engineering facilities located near a planned underwater aggregate extraction. The analysis was conducted in compliance with mining regulations and expert opinions. The study also aimed to assess the precision and correctness of the extraction, due to economic aspects. To reach the goals, in-situ research of the mining area was conducted, with the help of an advanced bathymetric device, based on the USV methodology. The instrument – named by the author as Smart-Sonar-Boat – was especially designed for underwater surveys in open-pit aggregate mines. The study analyzed the “Dwory” open-pit mine, located in southern Poland in the city of Oświęcim. The bathymetric results obtained contributed to improving the observation of changes in the bottom during the extraction. The applied USV method allowed for conducting the reliable evaluation of the mining work.
Switched reluctance motors (SRMs) are still under development to maximise their already proven usefulness.Amagnetic circuit of theSRMcan be made of soft magnetic composites (SMCs). The SMCs are composed of iron powder with dielectric and have a lot of advantages in comparison to commonly used electrical steel. The paper deals with the modelling and analysis of theSRMproduced by Emerson Electric Co. forwashing machines. Numerical calculations and modelling were done using the FEMM 4.2 program. Magnetic flux densities and magnetic flux lines were calculated, as well as electromagnetic torque and inductance for changing the position of a stator to a rotor. The obtained results were compared with other measurement results and are quite similar. The developed numerical model will be used for the project of a motor with an SMC magnetic circuit.
The paper presents results of compressive strength investigations of EN AC-44200 based aluminum alloy composite materials reinforced with aluminum oxide particles at ambient and at temperatures of 100, 200 and 250C. They were manufactured by squeeze casting of the porous preforms made of α-Al2O3 particles with liquid aluminum alloy EN AC-44200. The composite materials were reinforced with preforms characterized by the porosities of 90, 80, 70 and 60 vol. %, thus the alumina content in the composite materials was 10, 20, 30 and 40 vol.%. The results of the compressive strength of manufactured materials were presented and basing on the microscopic observations the effect of the volume content of strengthening alumina particles on the cracking mechanisms during compression at indicated temperatures were shown and discussed. The highest compressive strength of 470 MPa at ambient temperature showed composite materials strengthened with 40 vol.% of α-Al2O3 particles.
The paper presents selected granular ceramic materials available on the Polish market. Their characteristics have been determined in the aspect on application in the production of iron alloy-ceramic composite. The possibility of obtaining a composite layer by means of bulk grains in molds of plates were considered, which was the foundation for experimental molds to be used in service tests. On the basis of obtaining results was stated that the knowledge of the characteristics of bulk grains enables the calculation of their quantity necessary for the composite production. When using the bulk grains the thickness of the composite layer is restricted by the thermal relations (cooler) and the physical phenomena (buoyancy, metal static pressure). Increasing amount of grains above definite condition causes surface defects in the castings. Each casting, due to its weight, shape and place of composite layer production requires an individual approach, both at the stage of formation and that of calculation of the required quantity of ceramic grains.
Diagnostics of composite castings, due to their complex structure, requires that their characteristics are tested by an appropriate description method. Any deviation from the specific characteristic will be regarded as a material defect. The detection of defects in composite castings sometimes is not sufficient and the defects have to be identified. This study classifies defects found in the structures of saturated metallic composite castings and indicates those stages of the process where such defects are likely to be formed. Not only does the author determine the causes of structural defects, describe methods of their detection and identification, but also proposes a schematic procedure to be followed during detection and identification of structural defects of castings made from saturated reinforcement metallic composites. Alloys examination was conducted after technological process, while using destructive (macroscopic tests, light and scanning electron microscopy) and non-destructive (ultrasonic and X-ray defectoscopy, tomography, gravimetric method) methods. Research presented in this article are part of author’s work on castings quality.