Foundry resistance furnaces are thermal devices with a relatively large time delay in their response to a change in power parameters. Commonly used in automation classical PID controllers do not meet the requirements of high-quality control. Developed in recent years, fuzzy control theory is increasingly being used in various branches of economy and industry. Fuzzy controllers allow to introduce new developments in control systems of foundry furnaces as well. Correctly selected fuzzy controller can significantly reduce energy consumption in a controlled thermal process of heating equipment. The article presents a comparison of energy consumption by control system of foundry resistance furnace, equipped with either a PID controller or fuzzy controller optimally chosen.
Vacuum conditions in foundry installations are generated using electric-driven vacuum pumps. The purpose of the experiment is to evaluate the performance of a vacuum-assisted system for compaction of moulding sand basing on registered plots of selected electric power parameters of the power-supplying system of the pumps. Model testing done on an experimental vacuum system installation, power-supplied from a system incorporating the recorders of instantaneous current and voltage values. Following the numerical procedure, the experimental data are analysed to yield mathematical relationships between the variations of the generated vacuum pressure levels and variations of selected electric power parameters. Registered and computed values of selected parameters: instantaneous and RMS voltage and current values, active, reactive and apparent power levels and power coefficient allow for diagnosing the adequacy and reliability of the system operation. According to the authors, the applied monitoring of the power parameters of a vacuum-assisted installation may become an effective and easy practical method of evaluating the performance of such installations, used also in foundry plants.
In this article the main problems related with the proper choice of the design and operation parameters of vacuum installation in vacuum moulding system have been discussed. In such system a vacuum are generated using electric-driven vacuum pumps. The aim of the experiment is to evaluate the performance of a vacuum system basing on registered plots of selected electric power parameters of the power-supplying system of the pumps with parallel measurements instantaneous values of pressure in selected points of model stand. The measurements system for power-supply unit has incorporated the recorders of instantaneous current and voltage values. Following the suitable numerical procedure, the experimental data are analysed to yield mathematical relationships between the variations of the generated vacuum pressure levels and variations of selected electric power parameters. According to the authors, the applied measurements system of the parameters of a vacuum-assisted installation may become an effective and easy practical method of evaluating the performance of such installations, used also in industry.
Mechanization of the process of core making with the use of inorganic and organic binders is based, almost solely, on core blowing machines. Presently the core blowing machines are equipped with tools and devices that allow for application of different technologies of core making. Cold-box, hot-box and warm-air technologies require that core blowing machines shall be additionally equipped with either core-box pre-heating system or gas purging and neutralization system, or hot air purging systems. Considering the possibility of using varied, the most advantageous technologies of core making, the production of universal core blowing machines equipped with replaceable devices has been undertaken in Poland. The universal core blowing systems allow for mechanization of core making process also with the use of sand, bonded by modern, eco-friendly binder systems. The paper presents selected results-based evaluation of core blowing process showing the scope of conducted design and implementation works.
This article discusses the issue of the preparation of the foundry moulds with the use of an industrial robot. The methodology is presented for the determination of the process capacity index for placing inserts with flat and cylindrical faces. On the basis of the relationships developed, the process capability indices were determined at various points in the workspace, which are characterised by different values of the repeatability positioning error. It was shown that the value of the process capacity index can be increased by the selection of a suitable location for the process of placing the inserts in the workspace. It should also be noted that the value of the process's capability index depends on the selection of the place in the robot workspace where the process is carried out. Implementation of the joining process at an analysed point in the robot workspace leads to an increase of the process capability index MCp for inserts with flat faces up to 1.1 (+4.5%) and for inserts with cylindrical faces up to 1.3. This results in an increase of 13% to a level corresponding to the global standard for process reliability (MCp = 1.33).
Ensuring the required quality of castings is an important part of the production process. The quality control should be carried out in a fast and accurate way. These requirements can be met by the use of an optical measuring system installed on the arm of an industrial robot. In the article a methodology for assessing the quality of robotic measurement system to control certain feature of the casting, based on the analysis of repeatability and reproducibility is presented. It was shown that industrial robots equipped with optical measuring systems have the accuracy allowing their use in the process of dimensional control of castings manufactured by lost-wax process, permanent-mould casting, and pressure die-casting.
The paper presents the issue of production processes improvement in foundries in the area of finishing treatment of iron casts manufactured on automated foundry lines with vertical or horizontal mould division. Due to numerous factors which influence the efficiency of the processes, multi-criterion assessment tools were proposed in order to select the optimal solution for the assumed criteria. After determining the criteria weight using the Saaty method, a simulation experiment was designed and carried out which presents possible scenarios of casts finishing treatment operations. Basing on experiment reports from a computer model, particular solutions were evaluated using the Yager’s method. The evaluation of the experiment results was performed by experts who assessed different options according to each of the criteria adopted. After the establishment of the total standardized ratings by averaging the scores given by individual experts, the final decision was generated. Using the presented method, the best solution was chosen from among the analyzed scenarios.