The article discusses issues related to the generation, use, and transboundary movement of waste labeled with the code 191210 according to the waste catalogue regardless of its origin (municipal, industrial or mixed). Data contained in voivodship reports related to waste management and information about transboundary shipments shared by the Chief Inspectorate of Environmental Protection were also used in the article. The imbalance in the amount of produced and energetically used alternative fuels in Poland in the years 2015 to 2017 has been confirmed. This affects the economy of the waste management sector involved in the production of alternative fuels. The oversupply causes the prices of alternative fuels to fall and increases the need for subsidies in the case of the recovery or disposal of alternative fuels of lower quality. In the near future one should expect a stabilization of the supply of combustible waste to the cement industry, which is now beginning to achieve its technological potential; this is due to a high degree of replacement of fossil fuels. One should also expect an increase in the demand for alternative fuels from the commercial power sector and heating sector. It has been shown that much more alternative fuel is imported than exported from Poland. The amount of imported alternative fuel in the market is relatively low compared to the amount of fuel produced in the country. This oversupply affects, although not significantly, the possibility of using domestic waste for energy recovery. The export of the alternative fuel produced in the country is a favorable phenomenon when there is no possibility of sale on the domestic market. It seems rational, especially in the case of exports from installations producing fuels in border provinces.
In this work, the influence of microwave drying parameters such as irradiation time and microwave power level on the properties of synthetic moulding sands is presented. Determination of compressive strength Rc s, shear strength Rt s and permeability Ps of synthetic moulding sands with the addition of two different bentonites, after drying process with variable microwave parameters were made. The research works were carried out using the microwave oven with regulated power range of the electromagnetic field. From the results obtained, the significant influence of both drying time and microwave power level on the selected properties of moulding sands was observed. In comparison to the conventional drying method, microwave drying allows to obtain higher compressive strength of the synthetic moulding sand. The influence of application microwave irradiation on permeability was not observed. Higher strength characteristics and shorter drying time are major advantages of application of the electromagnetic irradiation for drying of the synthetic moulding sand with regard to conventional drying method.
A geodesic survey of an existing route requires one to determine the approximation curve by means of optimization using the total least squares method (TLSM). The objective function of the LSM was found to be a square of the Mahalanobis distance in the adjustment field ν . In approximation tasks, the Mahalanobis distance is the distance from a survey point to the desired curve. In the case of linear regression, this distance is codirectional with a coordinate axis; in orthogonal regression, it is codirectional with the normal line to the curve. Accepting the Mahalanobis distance from the survey point as a quasi-observation allows us to conduct adjustment using a numerically exact parametric procedure. Analysis of the potential application of splines under the NURBS (non-uniform rational B-spline) industrial standard with respect to route approximation has identified two issues: a lack of the value of the localizing parameter for a given survey point and the use of vector parameters that define the shape of the curve. The value of the localizing parameter was determined by projecting the survey point onto the curve. This projection, together with the aforementioned Mahalanobis distance, splits the position vector of the curve into two orthogonal constituents within the local coordinate system of the curve. A similar system corresponds to points that form the control polygonal chain and allows us to find their position with the help of a scalar variable that determines the shape of the curve by moving a knot toward the normal line.
In this article I deal with two social encyclical letters – Rerum novarum (1891) and Quadragesimo anno (1931). Also I undertake to discuss the views of Archbishop Wilhelm Emmanuel von Ketteler, who can be regarded as the most important forerunner of the ideas proclaimed later by Pope Leo XIII.
The article presents selected aspects of the life of Cecylia Działyńska against the background of her times, with a focus on the historical and cultural context as well as the specific local conditions, which had a considerable impact on her beliefs and attitude. The analysed source made it possible to reconstruct Cecylia’s convictions concerning her understanding of the nation, patriotism, attitude to the emancipation of women, social roles, faith and the Catholic church, which basically did not differ from the model convictions and behaviours in the public domain which were mandatory in the circles of women from the more enlightened spheres in the Prussian Partition. It was not so with the fulfilment of Cecylia’s ideals. Her deep religiousness, inclination to mysticism, unwillingness to marry, as well as an incurable, chronic disease, all left their mark on her life, preventing Cecylia from adopting the traditional role of a wife and a mother preserving the Polish customs and traditions, and maintaining faithfulness to the national and Catholic values in a family. Despite serious differences between the developing women’s movement in the Prussian Partition, and its equivalent in the Austrian and Russian Partitions, the views and the activity of women in the province of Posen, including Cecylia Działyńska (their rich charitable and educational activity as well as the significant development of female congregations in the second half of the 19th century), should be considered a more traditional, conservative model of the process of the emancipation of women on the Polish soil.
Cooling of the hot gas path components plays a key role in modern gas turbines. It allows, due to efficiency reasons, to operate the machines with temperature exceeding components' melting point. The cooling system however brings about some disadvantages as well. If so, we need to enforce the positive effects of cooling and diminish the drawbacks, which influence the reliability of components and the whole machine. To solve such a task we have to perform an optimization which makes it possible to reach the desired goal. The task is approached in the 3D configuration. The search process is performed by means of the evolutionary approach with floatingpoint representation of design variables. Each cooling structure candidate is evaluated on the basis of thermo-mechanical FEM computations done with Ansys via automatically generated script file. These computations are parallelized. The results are compared with the reference case which is the C3X airfoil and they show a potential stored in the cooling system. Appropriate passage distribution makes it possible to improve the operation condition for highly loaded components. Application of evolutionary approach, although most suitable for such problems, is time consuming, so more advanced approach (Conjugate Heat Transfer) requires huge computational power. The analysis is based on original procedure which involves optimization of size and location of internal cooling passages of cylindrical shape within the airfoil. All the channels can freely move within the airfoil cross section and also their number can change. Such a procedure is original.
The paper presents the results of laboratory tests into the effects of moisture and the content of two types of bentonite on dielectric properties of moulding sand. The use of electromagnetic waves in foundry industry is becoming more and more popular, which provides to some extent alternatives to conventional drying methods. Experimental studies published so far have shown the validity of using microwaves for drying classic moulding sands with bentonite. However, these studies lack data on the effect of moisture or bentonite content in moulding sand on the real component ε' or imaginary component ε'' of the relative complex electrical permittivity. The presented results may become in the future the basis for the evaluation of the composition of moulding sands, taking into account the phenomena occurring under the influence of electromagnetic field, which directly translates into the quality of the castings made and may constitute an attempt to develop a mathematical model of electric properties of moulding sands.