Applied sciences

Archives of Foundry Engineering

Content

Archives of Foundry Engineering | 2020 | Ahead of print |

Abstract

Simplifications used in simulation program codes require the use of substitute parameters in the material databases (also called apparent or substitutive). On the one hand, they formally fit into the records used in the heat flow model, porosity, properties etc. and on the other hand they should be determined in conditions most similar to the real casting-mould system.

The article presents results of a research on thermophysical parameters of gypsum mould used for precision casting moulds. Experiments were carried out on a cylindrical mould made of Plasticast gypsum, in which the heat source was a cylinder filled with liquid aluminium alloy of the temperature of 655°C. Energetic validation was carried out by using the NovaFlow&Solid ver. 6.3 simulation code. As a result of validation tests, substitute thermophysical parameters of gypsum were determined. For determined parameters, best-fit of solidification time from the experiment and simulation was obtained and the curves of gypsum mass heating were satisfactorily recreate.

Go to article

Abstract

An overview of the bibliography regarding the connection of knowledge about precious metal alloys and aspects of the use of computer aided technologies to the optimization of the jewelry casting processes is presented. An analysis of the usability of selected CAx systems was made: 1) for spatial design, called Rhinoceros 6 and 2) CAE system: NovaFlow & Solid (NF&S). The authors describe own research including data acquisition and evaluation of temperature variations during solidification of the selected Au-Ag-Cu alloy, with the identification of the phase transformations of this alloy. The intensity of heat exchange was changed (cooling of specimens under ambient temperature conditions – "normal" intensity and with the furnace – very slow cooling). The problem of completing the simulation database was pointed out and analyzed. Examples of simulations of casting selected jewelry (ring and signet) were given and compared with the result of the experiment realized in real conditions. It was confirmed that the optimization by combining experimental and simulation studies allows for the acquisition of new knowledge, and also facilitates the creation of new artistic designs of jewelry as well as performing the feasibility check, and then optimizing the chosen technology.

Go to article

Abstract

The article presents the results of permeability measurements of a zirconium alcohol coating applied on moulds and cores. The introduction extensively discusses the reasons for the application of protective coatings, as well as their advantages and disadvantages. Also, the problems related to the application of protective coatings are presented i.e. limited permeability and thus the possibility of the presence of gas-originated defects in the casts. Next, the paper discusses the methods of measuring the permeability of protective coating proposed by Falęcki and Pacyniak. The study also presents an indirect permeability measurement method. For the investigations, zirconium alcohol coatings with the three conventional viscosities 10, 20 and 30s were used. The viscosity was determined by means of the Ford cup with the clearance of 4mm. The coatings were applied onto profiles of Φ 50 x 50 mm, made of moulding sand consisting of a sand matrix with the mean grain size of dL = 0,11, 17, 24, 31 and 34 mm and phenol-formaldehyde resin. The effect of the matrix grain size on the permeability of the sand with and without a coating was determined.

Go to article

Abstract

The paper presents the results of investigations concerning the influence of gray cast iron modification on free vibration frequency of the disc casting. Three different chemical composition melts of gray cast iron were prepared in induction furnace. During gravity casting 0.05% and 0.3% mass of the Inolate modifier was added on stream of metal for changing graphite flakes in castings. Sound signal vibration of cast iron sample was registered by means on microphone for free vibration frequency measurements. Decreasing of free vibration frequency of modified cast iron in comparison with non modified castings was observed. Higher contents of modifier causes more decreasing of free vibration frequency. Cast iron with smaller contents of carbon and silicon have higher free vibration frequency in comparison with eutectic composition cast iron. Hardness of examined cast iron is lower when the more modifier is added during modification process. Free frequency is smaller with smaller Brinell hardness of disc casting. It was concluded that control of free vibration frequency of disc castings by means of chemical composition and modification process can improved comfort and safety of working parts.

Go to article

Abstract

The objective of the study reported in this paper was to determine the effect of structure on thermal power of cast-iron heat exchangers which in this case were furnace chambers constituting the main component of household fireplace-based heating systems and known commonly as fireplace inserts. For the purpose of relevant tests, plate-shaped castings were prepared of gray iron with flake graphite in pearlitic matrix (the material used to date typically for fireplace inserts) as well as similar castings of gray cast iron with vermicular graphite in pearlitic, ferritic-pearlitic, and ferritic matrix. For all the cast iron variants of different structures (graphite precipitate shapes and matrix type), calorimetric measurements were carried out consisting in determining the heat power which is quantity representing the rate of heat transfer to the ambient environment. It has been found that the value of the observed heat power was affected by both the shape of graphite precipitates and the type of alloy matrix. Higher thermal power values characterize plate castings of gray iron with vermicular graphite compared to plates cast of the flake graphite gray iron. In case of plates made of gray cast iron with vermicular graphite, the highest values of thermal power were observed for castings made of iron with ferritic matrix.

Go to article

Editorial office

CHIEF EDITORS
Editor
J. Szajnar
Deputy Editor
J. Jezierski

SUBJECT EDITORS
Theoretical Aspects of Casting Processes
K. Eigenfeld – Freiberg, Germany
E. Guzik – Kraków, Poland
T. G. Mathia - Lyon, France
W. Wołczyński – Kraków, Poland
Innovative Foundry Technologies and Materials
T. Elbel – Ostrava, Czech Republic
Z. Ignaszak – Poznań, Poland
O. P. Pandey – Punjab, India
A. Pereira - Vigo, Spain
Foundry Processes Computer Aiding
B. Mochnacki – Częstochowa, Poland
J. Roučka – Brno, Czech Republic
J.S. Suchy – Kraków, Poland
Mechanization, Automation and Robotics in Foundry
J. Bast – Freiberg, Germany
R. Wrona – Kraków, Poland
Transport Systems in Foundry
J. Dańko – Kraków, Poland
Z. Li – Shijiazhuang, China
Castings Quality Management
D. Bolibruchova– Żilina, Slovak Republic
J. D. B. de Mello - Santa Monica, Brazil
M. Perzyk – Warszawa, Poland
Environment Protection
M. Holtzer – Kraków, Poland
H. Polzin – Freiberg, Germany
J. Sobczak – Kraków, Poland
I. Volchok – Zaporizhzhya, Ukraine

EDITORIAL ADVISORY BOARD
J. Braszczyński – Częstochowa, Poland
B. K. Dhindaw – Rupnagar, India
L. A. Dobrzański – Gliwice, Poland
W. A. Hufenbach – Dresden, Germany
P. Jelínek – Ostrava, Czech Republic
L. Jeziorski – Częstochowa, Poland
J. Lacaze – Toulouse, France
V. L. Naydek – Kiev, Ukraine
A. Passerone – Genova, Italy
I. Riposan – Bucharest, Romania
F. Romankiewicz – Zielona Góra, Poland
A. Sládek – Żilina, Slovak Republic

INTERNATIONAL SCIENTIFIC REVIEW COMMITTEE
S. A. Argyropoulos – Toronto, Canada
M. Azadi – Tehran, Iran
Y. Babaskin – Kiev, Ukraine
K. Bako – Miskolc, Hungary
E. Bayraktar – Paris, France
L. Bechný – Zilina, Slovak Republic
V. Bednarova - Ostrava, Czech Republic
F. Bińczyk – Katowice, Poland
A. Bokota – Częstochowa, Poland
G.P. Borisov – Kiev, Ukraine
A. Bydałek – Kraków, Poland
C. H. Cáceres – Brisbane, Australia
J. Čech – Brno, Czech Republic
L. Q. Chen – Shenyang, China
A. Chojecki – Kraków, Poland
M. Cholewa – Gliwice, Poland
I. A. Dibrov – Moscow, Russia
D. Dispinar – Istanbul, Turkey
S. M. Dobosz – Kraków, Poland
V. I. Dubodelov – Kiev, Ukraine
A. Fedoryszyn – Krakow, Poland
J. Głownia – Kraków, Poland
K. Granat – Wrocław, Poland
J. Hampl – Ostrava, Czech Republic
J. Helber – Düsseldorf, Germany
M. Hetmańczyk – Katowice, Poland
M. Horáček – Brno, Czech Republic
M. Kaczorowski – Warszawa, Poland
W. Kapturkiewicz – Kraków, Poland
R. Kawalla – Freiberg, Germany
Z. Konopka – Czestochowa, Poland
D. Kopyciński – Kraków, Poland
W. K. Krajewski – Kraków, Poland
Z. Libo – Beijing, China
P. Lichy – Ostrava, Czech Republic
Y. P. Lim – Setapak, Malaysia
T. Lipiński – Olsztyn, Poland
E. Majchrzak – Gliwice, Poland
A. Mityayev - Zaporizhzhya, Ukraine
M. Murgaš – Trnava, Slovak Republic
I. Nová – Liberec, Czech Republic
W. Orłowicz – Rzeszów, Poland
T. Pacyniak – Łódź, Poland
B. Piekarski – Szczecin, Poland
A. Rimmer – West Bromwich, United Kingdom
S. Samavedam – Hyderabad, India
P. Schumacher – Leoben, Austria
N. Sczygiol – Częstochowa, Poland
P. Skočovský – Żilina, Slovak Republic
M.S. Soiński – Częstochowa, Poland
J. Sokolowski – Ottawa, Kanada
K. V. Sudhakar – Butte, USA
B. G. Thomas - Champaign, USA
M. Trbižan – Ljubljana, Slovenia
J. Vuorinen – Tampere, Finland
E. Ziółkowski – Kraków, Poland
J. Zych – Kraków, Poland

ASSOCIATE EDITORS
D. Bartocha – Gliwice, Poland, - editorial secretary
J. Suchoń – Gliwice, Poland - editorial secretary
J. Szymszal – Katowice, Poland, Statistic Editor
A. Dulska – Gliwice, Poland
M. Kondracki – Gliwice, Poland
C. Borek –Chicago, USA, Language Editor

 

Contact

ul. Towarowa 7,
44-100 Gliwice, Poland
e-mail: kikm@polsl.pl

This page uses 'cookies'. Learn more